answersLogoWhite

0

Yes,either above the A/C compressor or the altrnator(front of engine)

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Where is the crankshaft sensor on a 535i BMW 88?

First make sure it's actually a 88 and not a 87. On a 87 it has two sensors on the bellhousing, the one on the engine is diagnotic only. On a 88 it has a sensor either above the A/C compressor or the alternator.


1989 Oldsmobile delta 88 crankshaft sensor location?

The Crankshaft sensor is located behind the Harmonic Balancer on the front-passenger side


Where is a crankshaft sensor on 88 celebrity?

The location of the crankshaft position sensor depends on which engine the car has. If it is the 2.5L 4 cylinder engine the crankshaft position sensor is behind the ignition module. If it is the 2.8L V6 engine the crankshaft position sensor is on the side of the engine nearest the firewall and just above the pan rail in about the center of the block.


How do you do you change the crankshaft positioning sensor on a 1992 Oldsmobile 88?

To change the crankshaft positioning sensor on a 1992 Oldsmobile 88, first, disconnect the negative battery cable for safety. Locate the sensor, which is typically found near the crankshaft pulley, and remove any components obstructing access. Unscrew the old sensor, disconnect the wiring harness, and install the new sensor by reversing the process. Finally, reconnect the battery and check for proper operation.


When do you change the oil on an 1988 BMW?

Looking at the engine, all the way to the back of the block, on the left side. Right behind the air filter. It should be a black cap. That's where it is on my 88' 535i


How do you locate a crankshaft sensor on a 1988 Oldsmobile Delta 88?

To locate the crankshaft sensor on a 1988 Oldsmobile Delta 88, first, ensure the vehicle is safely elevated and the battery is disconnected. The crankshaft position sensor is typically found near the engine's crankshaft, often at the front or rear of the engine block or near the timing cover. You may need to remove some components, like the air intake or accessories, for better access. Consult a repair manual for specific diagrams and detailed steps for your model.


Where is the crank sensor on a 1999 Oldsmobile 88?

On a 1999 Oldsmobile 88, the crankshaft position sensor is typically located near the lower front part of the engine, often on the engine block near the crankshaft pulley. To access it, you may need to remove any obstructions, such as the engine cover or other components. The sensor is usually mounted with a couple of bolts and connected by an electrical connector. Always refer to the vehicle's service manual for specific details and procedures.


How do you change a crankshaft sensor on a 1987 olds delta 88?

You have to remove the Vibration Damper first, then you will have clear access to the Crank sensor. Make sure when you reinstall it, the wires don't get caught in the Damper assembly and you have clearance where the sensor mounts. Easy fix.


Where is the Crankshaft sensor on 1997 Oldsmobile 88?

On a 1997 Oldsmobile 88, the crankshaft position sensor is located on the engine block, near the rear of the engine, close to the transmission bell housing. It is typically mounted on the driver's side and may require removal of some components for easier access. To locate it, you may need to look beneath the vehicle or remove the engine cover, depending on the specific configuration of your engine.


What is the best batterysuitable for a 1992 BMW 27.66 or 88?

OEM BMW Batteries are always the best to reinstall into a BMW.


What is code22 on 93 olds 88?

Code 22 on a 1993 Oldsmobile 88 typically indicates a problem with the vehicle's ignition system, specifically relating to the crankshaft position sensor or the ignition module. This code can lead to issues such as poor engine performance or stalling. To resolve the issue, you may need to inspect and possibly replace the crankshaft position sensor or related ignition components. It's advisable to use a diagnostic scanner to confirm the code and guide repairs.


What is the wheel lug torque of a BMW 335i?

88 lb-ft