answersLogoWhite

0

is very simple, just remove the plastic cover from the engine, locate the ignition coil that you want to replace, but before you disconnect the ignition coil disconnect one terminal from the battery and make sure that doesn't touch the chassis from the car and then disconnect the wires connector from the ignition coil and remove the two scrawls from the ignition coil and install the new one and make sure you replaced the washer that goes at the baton of the coil and reconnect the wires connector back and reconnect back the terminal from the battery on some times went you disconnect the battery your radio may go into safe code make sure you have the code to reprogram you radio again before you do this procedure

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How do you replace a coil on 2003 Chevrolet Express?

REMOVAL PROCEDURE Remove the engine cover. Disconnect the spark plug wires at the ignition coils. Disconnect the ignition coil harness connector. Remove the ignition coil mounting bolts. Remove the ignition coil. INSTALLATION PROCEDURE Install the ignition coil to the bracket. Install the ignition coil mounting bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten Tighten the ignition coil mounting bolts to 8 N.m (71 lb in) . Connect the ignition coil harness connector. Connect the spark plug wires at the ignition coils. Install the engine cover.


How do you install ignition coil on 1999 Lexus rx 300?

Each spark plug has it's own ignition coil, they are on the spark plug itself. Unplug the ignition coil connector, remove the bolt holding the coil in place, pull the coil off of the spark plug and out of the valve cover. Install the new coil.


Volkswagen Passat Questions How many ignition coils are there in a 2004 Volkswagen Passat 1.8 Lt. 4 Cy.?

Each cylinder has it's own separate ignition coil. The 1.8 T has four cylinders, so there are four ignition coils.


How do you install ignition coil for 2002 GMC safari?

with a mechanic


How do you install an ignition coil in a 2005 Chevy Malibu?

It is very difficult to get the old one off. You have to take a torch and melt the old one down and then spoon it out like pudding.


How do you replace a 1970 Chevy ignition coil?

take the wires off the + and - side of the coil, pull the coil wire out of the coil, unbolt the coil from the manifold, to install just reverse directions.


Location of ignition coil on 2005 ford 500?

each spark plug has its own ignition coil on top of the plug, like many current cars.


How to install ignition coil on a 1993 3.1 liter?

To install the ignition coil on a 1993 3.1-liter engine, first disconnect the negative battery cable for safety. Remove the old ignition coil by unplugging the wiring harness and unscrewing any mounting bolts. Position the new ignition coil in place, secure it with the bolts, and reconnect the wiring harness. Finally, reconnect the negative battery cable and start the engine to ensure proper operation.


Where is the coil pack on a 2005 Chevy Trailblazer?

The 2005 Chevy Trailblazer has Coil-On-Plug ignition coils so there are 6 "coil packs". Each one is mounted on top of the spark plug.


How do i install a resistor on a 04' Yamaha r6 ignition?

To install a resistor on a 2004 Yamaha R6 ignition, first, locate the ignition coil wires. Disconnect the battery to ensure safety, then cut the ignition wire where you want to install the resistor. Connect one end of the resistor to the cut wire leading to the ignition coil and the other end to the wire leading to the ignition switch, ensuring secure connections with solder or connectors. Finally, reassemble everything, reconnect the battery, and test the ignition system.


Where the ignition coil is located at on a 1993 dodge colt 1.8 liter Im trying to install a tach?

in side dist under pickup coil


How do you install an ignition coil on a 6.75 hp Briggs and Stratton?

To install an ignition coil on a 6.75 hp Briggs and Stratton engine, first, ensure the engine is off and disconnect the spark plug wire. Remove any necessary covers and unbolt the old ignition coil from the engine block. Position the new ignition coil in place, ensuring the magnet aligns with the flywheel, and then secure it with bolts. Finally, reconnect the spark plug wire and replace any covers before testing the engine.