0
In a Peugeot 307, the wires to the windscreen washer pump are typically colored blue and green. However, wire colors can sometimes vary based on the specific model and year, so it's important to refer to the vehicle's wiring diagram for accurate information. Always ensure the vehicle is off and securely grounded before working on electrical components.
What else can I help you with?
Why should the windscreen wipers on your peugeot 406 LXTD decide not to work on first time of asking from a cold start. They work after a time and much fiddling with the control.?
its a faulty connexion. wires may be broken or torn. get it checked out
Where and how do you change a windscreen washer pump on a 1997 Hyundai Lantra?
in front of the right front tire, remove lower plastic guard and pump is attached to fluid tank.... pull pump off and jump back as fluid drains out of tank... after fluid is gone unplug wires then plug wires in new pump and push pump into tank
What colors are the speaker wires in a 1993 Peugeot 106?
grey
Where is the windshield washer motor on your 86 f150?
it is in the same tank that you put the washer fluid in /// in the bottom of it , it has 2 wires and a black hose going to it on the outside bottom of the tank. it is in the same tank that you put the washer fluid in /// in the bottom of it , it has 2 wires and a black hose going to it on the outside bottom of the tank.
Why has my Honda jazz windscreen washer stopped working?
3 reasons the motor in the blade for the windshield has burnt out, the wires are burnt or the switch behind the steering wheel has died strange enough if all fail the the car to the Honda company and report the problem also the car might be second-hand which the original ower didn't know
How do you find the speaker wire in a peugeot 306?
In a Peugeot 306, the speakers are located inside the front doors. There should be four wires total, two for the speakers and two for the tweeters.
What is the colour code for neutral in electrical wires in Ghana?
Black
What colour wire is the reversing lights on a 406 peugeot?
On a Peugeot 406, the reversing light wires are typically green and brown. The green wire is generally the positive connection, while the brown wire serves as the negative. However, it's always best to consult the vehicle's specific wiring diagram for confirmation, as colors may vary slightly between models or production years.
Where is the washer pump located on a 1992 Mercury Grand Marquis?
It should be inside the Washer Fluid Holding Tank. Look on the bottom for wires coming off the tank.
How do you replace the windscreen washer pump on a Daewoo Lanos 1999?
very simply. Remove front passenger side wheel, there is a plastic mud gaurd like sheet that is between wheel and engine bay. remove this enough to allow you to work, three small bolt screws, 1 underneath and 2 on the side, also a plastic clip that kinda pulls off but to the right, once you can pull the plastic casing back enough to see in, the washer bottle is right behind. 2 wires go to each pump. there are two pumps 1 for front windscreen and 1 for rear. remove the wires by pulling them off the clip on connection then pull off the two hoses for the water, next the motors can be pulled from the bottle, they are only held in with a rubber seal. very simple just did mine for the first time in half hr.
How do you change a wig-wags on a washer?
To change the wig-wags on a washer, first unplug the appliance. Locate the old wig-wags under the control panel or inside the machine and carefully remove them by disconnecting the wires. Install the new wig-wags by connecting the wires and securing them in place. Finally, test the washer to ensure the new wig-wags are functioning correctly.
How do i fix wires for electronic window for my Peugeot 307cc?
To fix the wires for the electronic window in your Peugeot 307CC, first, remove the door panel to access the wiring harness. Inspect the wires for any visible damage or breaks, and use electrical tape or heat shrink tubing to repair them. If the wires are severely damaged, consider replacing the entire wiring harness. Finally, reassemble the door panel and test the window functionality before securing everything back in place.
