Here are a few tips for using the Scotts AccuGreen 1000 Drop Spreader:
* Always fill on a flat surface, other than the lawn.
* Check the back of the bag for proper spreader settings.
* Avoid streaks by slightly overlapping each strip with the previous strip. This can be done by lining the wheel track up with the ARROW on the top edge of the hopper.
* Use a walking speed of approximately 20 feet every 5 seconds.
* If your lawn is rectangular, apply product the longest direction. Apply two header strips across each end for a turning area. (HEADER STRIPS ARE SIMPLY TO BORDER THE LAWN IN ORDER TO PROVIDE AN EVEN APPLICATION) Steer smoothly around obstacles, keeping wheel away from any area you do not wish to treat.
CAUTION: Exercise care around ornamental plants, because weed controls can damage them.
* If your lawn is an irregular shape, apply a header strip completely around it. Then apply product back and forth in the longest direction.
Yes one can use Vigoro spread with a Scotts spreader. The amount of Vigoro spread that needs to be used must be correlated in retrospect with the size of the area needing the spread.
To adjust calibration, do the following:A) Adjust the micrometer setting to 11.B) Squeeze the trigger against the handle.C) The calibration line engraved on the top of the shutoff plate should be flush with the back edge of the hopper opening.D) To adjust alignment, use a small wrench or pliers to turn the black calibration screw at the lower end of the control wire leading from the micrometer rate setting barrel.http://www.scotts.com/smg/goART2/InfoHowTo/spreader-settings-for-grass-seed-and-lawn-food/19500090/7200009
A) Adjust the micrometer setting to 2.B) Squeeze the trigger against the handle.C) The calibration line engraved on the top of the shutoff plate should be flush with the back edge of the hopper opening.D) To adjustalignment, use a small wrench or pliers to turn the black calibration screw at the lower end of the control wire leading from the micrometer rate setting barrel.http://www.scotts.com/smg/goART2/InfoHowTo/spreader-settings-for-grass-seed-and-lawn-food/19500090/7200009(MORE)
There is no such measure such as militers. Assuming that you mean millilitre, you multiply litres by 1000.
1000 billion / 4.5 billion = 1000/4.5 = 222.22... years.
Yes one can use Vigoro spread with a Scotts spreader. The amount of Vigoro spread that needs to be used must be correlated in retrospect with the size of the area needing the spread.
You would want to use spreader setting 3.25
The correct setting for an EZ broadcast spreader by republic is 3. Many persons have used this code and it has worked perfectly for them. Depending on what you are doing you can also use the number 4 setting.
Set the Scott's Speedy Green 1000 spreader to the recommended setting for the 20-1-4 Naturlawn nutrient as indicated on the product packaging or by using a calibration test. Apply the fertilizer evenly over your lawn, ensuring to follow all safety and usage instructions provided.
it's just called a crepe spreader
I use rock salt to melt ice and use my brocast spreader to scatter it on my driveway. I have also used the spreader to apply other ice melting products as well with no problem.
The RDRAM and the DRAM are the memory technologies that use the heat spreader. These memory technologies usually have a high technology.
Using a cheese spreader as oppossed to a knife will get you much smoother results. Knives tend to be narrow and cant spread some of the runnier cheeses as well as a spreader which is wide and easier to maneuver.
EZ broadcast spreader, you ought to counsel the item's bundling or mark. The bundling ordinarily incorporates nitty gritty directions and a proposed spreader setting outline well defined for the item. This diagram will normally give rules to different spreader models and their comparing settings. Search for the particular model of your EZ broadcast spreader on the diagram and follow the comparing suggested setting for Scott's Reward S Weed and Feed. It's critical to take note of that various spreaders might have different mathematical scales or dial settings, so make certain to allude to the particular guidelines given by Scott's or counsel their client assistance for exact data. EZ broadcast spreader while applying Scotts Reward S Weed and Take care of will rely upon the particular model of the spreader and the pace of use indicated on the item mark. To decide the right setting for your spreader, you can allude to the item name, which will give guidelines to application rates and spreader settings. The mark may likewise incorporate a graph with suggested spreader settings for different models of spreaders. It is critical to follow the prescribed spreader settings and application rates to guarantee legitimate inclusion and compelling control of weeds. Utilizing some unacceptable setting can result in finished or under-use of the item, which can prompt unfortunate outcomes or harm to your grass.
This is a tricky question since there are different kind of scott spreaders and the lesco products doesn't list the settings for all of the scott's spreaders. I use the standard Scott spreader. What I figured out is that the spreader number represents the amount of pounds of product per 1000 sq ft. Example: if you want to apply 4lbs/1000 sq ft of product then use setting 4. If you want to apply 8lbs/1000 sq ft then use setting 8. Always remember not to go over the maximum amt of product per year. This is important when applying lesco pre-emergent and post-emergent since it can affect the PH of the soil. I also found this chart. The standard Scott spreader setting goes from 1 to 18.GENERIC SETTINGS - Rotary / Broadcast SpreadersApplication Rate3 lbs/1,000 sq. ft4 lbs/1,000 sq. ft5 lbs/1,000 sq. ftSpreader Range1 -- 102½3½41 -- 183451 -- 241416181 -- 40253033
To adjust calibration, do the following:A) Adjust the micrometer setting to 11.B) Squeeze the trigger against the handle.C) The calibration line engraved on the top of the shutoff plate should be flush with the back edge of the hopper opening.D) To adjust alignment, use a small wrench or pliers to turn the black calibration screw at the lower end of the control wire leading from the micrometer rate setting barrel.http://www.scotts.com/smg/goART2/InfoHowTo/spreader-settings-for-grass-seed-and-lawn-food/19500090/7200009
You would want to use a spreader setting of 3.5. Go over the entire lawn 1 time.