0
Why the flow rates of water affect the difference of inlet and outlet temperatures?
The flow rate of the water determines the cooling load.
As you increase and decrease the flow, the load is being increased and decreased.
The system is designed to be most efficient at a certain specific load, and it is at that point that the COP will be at it's maximum. Any flow rate above and below that point will decrease the COP.
What else can I help you with?
Advantages of Bunsen burner?
Because of the adjustable air inlet you can get flames of various temperatures.
Difference bw ostia and osculum?
ostia is the inlet into the sponge and osculum is the outlet through which the entered water etc. moves out
How does a ice maker water inlet work?
An ice maker water inlet is a valve that controls the flow of water into the ice maker, typically found in refrigerators. When the ice maker needs water to create ice, it sends a signal to the inlet valve, which opens to allow water from the household supply line to flow into the ice mold. Once the mold fills, the valve closes until the next cycle. This process is automated and ensures a consistent supply of ice as needed.
Is marble permeable or impermeable?
Marble is stone that is generally polished and used in fine building work, furniture, or decorative art. It may be white or colored. It is porous, and easily stained. Marble is etched by acids. Wipe off anything spilled on marble immediately, as you would on a wood surface. Avoid setting beverage glasses directly on marble as they leave rings.
No hot water pressure throughout the house?
Check the H/W tank and possibly clean it out: - You first turn OFF the power to tank, then attach a hose pipe to the bottom fitting, lead it outside or to any drain, turn on the valve by it, turn OFF your inlet valve and open the relief valve so air can enter the H/W tank.Let the whole tank empty -takes about 30 -40 minutes. Next, when empty turn ON the inlet valve and let cold water run through the tank and out the hose, now you will see the sludge coming out. Let this run 5-7 minutes or until water is coming through clean. Now you are done . Let it fill, then turn on power.
What is manometric head?
it is the pressure difference between inlet and outlet of pump.
Is there any difference in temperature at inlet and outlet of steam turbine?
For efficiency's sake, the outlet had best be a lot cooler.
Which is Fuel pump inlet and outlet?
Inlet line will be bigger then the outlet line. on the contrary on my motorcycle fuel pump, the inlet and outlet are the same size!
Does heat energy make wires in a generator spin?
In a way. It is the difference between temperatures at the inlet and outlet of the steam turbine (generically, a 'heat engine') which results in the turbine spinning -this, in turn, causes the generator to spin.
What is range in cooling tower?
Range is the difference of cooling water inlet and cooling water outlet temp
Hot Approach and Cold approach in heat exchanger?
Hot Approach: It is difference in temperature of hot fluid inlet temperature and cold fluid outlet temperature Cold Approach: It is difference in temperature of Hot fluid outlet temperature and cold fluid inlet temperature. Mohsin
What is the inlet and outlet valve clearances on a 1975 Ford cortina 1600?
valve clearance hot - inlet mm 0,3 and outlet 0,56
Where is the low and hi side on a ac compressor?
The inlet side is the low side - this will have the larger hose. On a Thermal Expansion Valve system, this hose will run from the evaporator outlet to the compressor inlet. On a Fixed Orifice Tube system, this hose will run from the accumulator outlet to the compressor inlet. The outlet side is the high side, and the hose will run from the compressor outlet to the condenser inlet.
What are my options for plumbing fixtures with more than one inlet and outlet?
A tee is a plumbing fixture with one inlet and two outlets, or two inlets and one outlet. A cross is a fixture with one inlet and three outlets, or three inlets and one outlet.
What are the names of all the water hoses in a car?
Upper and lower radiator, inlet and outlet heater core, bypass,Upper and lower radiator, inlet and outlet heater core, bypass,
Does a pond have an inlet and outlet?
Generally a "pond" is taught of as a still body of water smaller than a lake. "still" implies no flow movement and would mean that there is no inlet or outlet. However, the term "pond" is sometimes extended as in "Mill Pond" which would have both an inlet and an outlet.
What is it called where a river reaches the sea?
Inlet or outlet
