answersLogoWhite

0

A 3-way switch controls the power at a light by allowing you to turn the light on or off from two different locations. This is achieved by using two 3-way switches connected to each other and the light fixture, creating a circuit that can be toggled on or off from either switch.

User Avatar

AnswerBot

4mo ago

What else can I help you with?

Related Questions

How do you control a lamp from three different positions?

we use 2-3way switch and 1-4way switch


How do you wire a one light to be operated from 4 location?

you will need 2-3way switch and 2-4way switch


How do you connect two way electrical switch?

The two way switches work in pairs. We find most of them in our houses where the light bulb can be operated by two switches each at the far end to the other. Each switch consists of three terminals two of which are connected. When one switch is open and the other is closed then the bulb glows and viceversa


What does a 4 way switch do?

For starters, a four way switch must be connected to either a four way switch or a three way switch on either side. Said differently, here are some common combinations: 3way---------4way-----------3way 3way---------4way-----------4way------------3way 3way---------4way-----------4way------------4way----------------3way etc. If you are using a four way switch anywhere in a circuit both ends must have three way switches. You can use as few as one four way between the three ways, or as many as you would like. First of all, connect your white (neutral) wire straight through every box, from the power source to the light fixture being controlled. That neutral has nothing to do with the switches. On your three way switches you will see two bright screws and one dark. (Excluding the green grounding screw). One three way switch will have its dark screw connected to the power source. Two wires will run from the bright screws to the next box (the 4 way switch box). Those two wires will connect to the two bright screws on one side of the four way. The four way also has dark screws, but two of them. Connect two wires to these two dark screws, and run them to the next switch box. If the next switch box is another 4 way, repeat this again and again until you get to the last switch (a three way). Wire the last three way as follows: the two wires coming from the previous 4 way go to the bright screws. The hot wire feeding the light fixture will be the one to connect to the single dark terminal of the last 3 way switch. That's it! As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


How do you insulate 3way valve for the fcu?

You insulate the 3way valve for the FCU to control temperatures. If the valve is left uninsulated, the contents will either lose or gain temperature depending out external conditions.


How is one light controlled by three switches?

That is called a 4 way light switch circuit. On each end of the circuit you install a 3way switch and in the middle you install a 4 way switch.Answer using British TerminologyIn the UK, 'three-way' switches are called 'two-way' switches (more logical, if you think about it!), and the 'four-way' switch is called an 'intermediate' switch.


Wiring diagram for a 3way motion light sensor?

wiring diagram for a 3 way motion light sensor


How do you control 2 lamps with two way switch?

A 3way switch at each location is what you use, but it must be wired properly to work. You must have incoming power at one switch location and no power at the other location. The other location has the wire going up to the light. You then need a 3 conducted wire such as 12/3 or 14/3 running between the switches. Use the same size wire you used to power the switch and top up to the light. You then connect the black power wire at one location to the black screw on the switch, and at the other location you connect the black wire going to the light to the black screw on that switch. At each location tie the whites together under a wire nut and shove that back in the box. Tie the grounds together and connect that to the ground screw at each switch. At each location you will now have the black and red wire from the wire you ran between the switches left. Those are called travelers. Connect those wires to the remaining 2 screws left on the switches at each location. Does not mater which you connect to which screw. Assuming no other wires are involved this is how you wire it.


Can you replace a 3-way light switch with a standard switch and cap off the wires or can you use the 3-way switch and make it into a standard switch?

It can be done but it requires knowledge about how a 3way is wired to convert it to a regular switch. It would involve testing live wires to determine where power starts at. You can't just replace one switch.


What are the release dates for 3Way - 2008?

3Way - 2008 was released on: USA: 4 February 2008 (Los Angeles, California)


What are the release dates for 3Way - 2008 Psychodrama 1-7?

3Way - 2008 Psychodrama 1-7 was released on: USA: 7 April 2008


What are the release dates for 3Way - 2008 LadyCops Brotherly Love?

3Way - 2008 LadyCops Brotherly Love was released on: USA: 6 July 2009

Trending Questions
What is the purpose of a sprinkler pressure vacuum breaker and how does it help in maintaining the proper pressure in a sprinkler system? How can I properly prepare wood for staining, including the crucial step of pre-staining to ensure a smooth and even finish? What is the best flooring gap filler to use for filling gaps in hardwood floors? How can I effectively apply oil-based or water-based polyurethane to protect and enhance the finish of my wood furniture? What is the imitation diamond called? What is the different in a vertical rudder and a horizontal? How can I create a DIY wood filler for repairing furniture and other wooden items? Can wall tile be used on the floor? What are the benefits of a smoke detector with a strobe light for individuals with hearing impairments? How can I attach wood to a concrete block? What size refrigerator do I need for my kitchen space and storage requirements? How can I stop a running toilet? What are the benefits of using temporary floor tiles for home renovation projects? What safety precautions should be taken when installing a 240v receptacle in a residential setting? What are the best application techniques for achieving a smooth and durable finish with polyurethane clear coat on wood surfaces? Where can I find high-quality gloss black furniture paint for my next DIY project? Why is the light on my new ceiling fan not working even though the fan itself is functioning properly? How can I effectively laminate boards for a durable and long-lasting finish? How do you masurbate for girls? How can I create a precise and clean cut groove in wood for my woodworking project?