answersLogoWhite

0

You need a good socket set and a torque wrench. Remove plastic covers from right and left sides. Belt guides must be loosened (but do not take nuts completely off, just enough to get new belt on), Start the belt from the back and work it over the left and right guides, tighen nuts (torque back to 35 lbs), then work belt around the tension guide, now with torque wrench still on tensioner, use the wrench to pull the tensioner forward and work belt over the front engine puller, tighten tension pully nut to 35 pounds and replace covers. I use Honda-tight (blue) will all nuts and fastners.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How to install a Drive Belt on a John Deere LX188?

i need a diagram for installing a belt on a john deere lawn mower 330


Drive belt installation John Deere GT262?

To install the drive belt on a John Deere GT262, first, ensure the mower is turned off and the battery is disconnected for safety. Remove the mower deck by disengaging the pins and lifting it off. Next, locate the old drive belt and note its routing before removing it. Install the new belt by threading it through the pulleys in the same configuration, ensuring it is properly seated, and then reattach the mower deck. Finally, reconnect the battery and test the mower to ensure the belt operates smoothly.


How do you install the mower deck on a LT133 tractor?

The deck must be slipped beneath the machine from the left, the lift lever locked down and the rear hangers and front hanger plate attached. The belt will take take a 90 degree twist with the front part to the left side.


How do you change the drive belt on a John Deere 260 lawn mower?

To change the drive belt on a John Deere 260 lawn mower, first, ensure the mower is turned off and disconnected from the power source. Remove the mower deck by detaching any necessary bolts and pins, then locate and remove the old drive belt from the pulleys. Install the new belt by routing it according to the diagram usually found on the mower or in the owner's manual, ensuring it fits snugly on all pulleys. Finally, reattach the mower deck and double-check the belt alignment before testing the mower.


L120 48'belt diagram for john deere lawn mower?

need a quick reference guide on diagram of belt drive for a l120 john deere lawn mower


How do you change drive belt on a John Deere 345?

To change the drive belt on a John Deere 345, first, ensure the engine is off and disconnect the spark plug for safety. Remove the mower deck by detaching it from the tractor, then locate the drive belt. Remove the old belt by releasing the tension from the belt tensioner, and install the new belt by routing it according to the diagram typically found on the mower deck or in the owner's manual. Finally, reattach the mower deck and reconnect the spark plug before testing the setup.


Do you have a picture of routing a drive belt on a mower deck?

john deere LT155 38inch cut mower deck


The illustration on the drive belt routing on your john deere gt225?

i need diagram on how to replace deck belt on John Deere GT235 mower


What is the correct deck belt for a jd 210?

John Deere 210 38" mower deck drive belt: M40223 secondary drive belt


How do you install a 42 deck belt on John deere LX255 Lawn Mower?

One might learn how to install a 42 inch deck belt on a John Deere lawnmower by looking at their user manual. A better route to this may be to take it to a lawn mower shop for repair.


How do you replace a drive belt on lx178?

To replace the drive belt on a John Deere LX178, first, ensure the mower is turned off and disconnect the battery for safety. Remove the mower deck by loosening the necessary bolts and detaching the drive belt from the pulleys. Install the new drive belt by threading it around the pulleys in the correct routing, ensuring it is properly seated. Finally, reattach the mower deck and reconnect the battery, checking that everything operates smoothly before use.


How do you replace a main drive belt on a John Deere GT262?

To replace the main drive belt on a John Deere GT262, first ensure the mower is off and disconnect the battery for safety. Remove the deck by detaching the necessary bolts and the belt guard, then take off the old belt from the pulleys. Install the new belt by routing it around the pulleys in the same configuration as the old one, ensuring it is properly seated. Reassemble the deck and reconnect the battery before testing the mower.