0
How can you read the air condition compressor tag to identify the capacity or BTU when it has no LRA and FLA just it has serial number?
Wiki User
∙ 12y ago
The only way is to contact the manufacturer or supplier with the model number at hand, normally it is the large number that is on the ID plate
The only way is to contact the manufacturer or supplier with the model number at hand, normally it is the large number that is on the ID plate
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the function of the Turbine Section of the Industrial Gas Turbine?
It does a number of things depending on what type of engine its coming from, but in all engines, it extracts energy from the combustion gasses and turns the shaft which also turns the compressor section.
What are the advantages and disadvantages of axial compressor?
Axial-flow compressors have the following advantages: -High peak efficiency. -Small frontal area forgiven airflow. -Straight-through flow, allowing high ram efficiency. -Increased pressure rise due to increased number of stages with negligible losses. They have the following disadvantages: - Good efficiency over narrow rotational speed range. -Difficulty of manufacture and high cost. -Relatively high weight. -High starting power requirements (this has been partially overcome by split compressors).
Wheel load calculation of crane?
Calculation of crane related The crane wheel load, usually referred to as maximum wheel load is the total load in pounds that any single crane wheel will see. The formula for determining MWL is Bridge weight / 2 + {Live load ( crane capacity + hoist weight) x 15%impact*)/ Number of wheels on a single end truck. For a top running 5-ton capacity crane, with a bridge weight of 8000 lbs. and a hoist that weights 900 lbs. with four wheels total: 8000/2+(10000+9000x1.15)/2=12925 *15% impact for hoist speeds under 30 fpm in CMAA Class C Service
What is definition of fluctuating load?
The type of loads that vary continuously on the structure or a body are called fluctuating loads . for example traffic passing on a bridge applies different loads of varying nature.When load is fluctuating , the maximum stress level condition appears frequently . number of loading cycle is a count which tells that how many times the structure can bear maximum stress level.So fluctuating loads reduce the endurance limit.
Loading unloading valve working of screw compressors?
Pressure regulation is accomplished by the use of free air unloading.The purpose of such control to unload theair compressor.When more air is being compressed than is being consumed.Thus reducing to a minimum the power required to drive the compressor and providing maximum economy during the unloading period.This control was done by manual operated type unloaders such as "M" type or "W" type unloaders.Actually this is old technology and replaced by "Electro-Pneumatic Controls" which is also replaced by "Program Logic Control".Still many companies are using old technology and therefore,I am giving details about "M" Type Unloader. * The operation of the unloader is simple and positive.When the pressure in the airdischarge line from the compressor to the receiver reaches the pressure point at which the unloader is set to operate,as determined by the position of the adjusting screw,the plate valve is forced away from its seat on the unloader body.When this happens,air from the discharge line from the compressor to the receiver passes through the unloader and to the unloading suction valve covers,holding these valves open.Then the compressor operates against the atmosphere pressure only. * When the air pressure in the discharge line from the compressor to the receiver is reduced to the predetermined pressure setting of the unloader as determined by the number of unloader shims,then the compression of the spring,over-comes the pressure of the air in the discharge line from the compressor acting against the plate valve,forcing the valve back against its seat on the unloader body.The air trapped in the unloader piping is then vented out to the atmosphere through the vent hole of unloader. * The pressure at which the unit will unload is determined by the position of the adjusting screw.Turning this screw in,increase the compression pressure on the spring and the unloading pressure of compressor.Turning the screw out,lower the unloading pressure.To decrease the loading-unloading range,add the shims and to increase the range,remove the shims. * The most important care that the unloader should receive is to be kept clean.If the operation of it becomes sluggish,the operator should first make sure that all unloader piping is free from leakages since leakage from these places will affect the operation of the unloader.Also the vent hole in the unloader valve seat is open.The gauze of the air cleaner in the unloader line should be removed and cleaned.If problem is not solved,remove the unloader valve seat and clean.If the cleaning and adjusting fail to make the unloader operate satisfactorily,the valve may require grinding. * Use fine grinding compound for valve seat grinding.The valve is provided with two small holes on the top surface for the insertion of the tool to turn it in grinding.Avoid excess grinding since this may change the point of contact sufficiently to affect operation adversely.Clean out all the compound thoroughly after grinding.
Identify the simple subject in the sentence there are too many people on this elevator?
All elevators have a certain capacity that they must maintain. There is not a number of people that must be adhere to but a certain weight capacity.
What is the value of a 32 Belgian Browning automatic stamped WAa140 in good condition?
These number don't identify what the gun is, nor is it a Browning Serial number. What do you mean by "32"?
What is the worth of e Remington and sons 22 octagonal barrel number 15869?
Octagonal barrel could be a plethora of different guns anywhere from a rolling block to a pump. Need to identify what it is first and condition, condition, condition for values.
What is the ability to identify and account for NWRM by serial number and to be cognizant of the condition and location of these items in near real time?
Positive Inventory Control (PIC)
What is value of mint condition 3 cents Abraham Lincoln US Postage Stamps?
There are a number of 3 cent Lincoln stamps. Value will depend on the version and condition. Consult a catalog to properly identify the stamp.
What is the value of a 12 gauge Winchester pump shotgun model 1839039 F?
You have supplied the serial number to your shotgun.I would need the model number to identify the value of your shotgun,along with its overall condition.
Why your air condition is blowing out hot air and it has freon?
Could be a number of reasons. You may not have enough refrigerant. You may have a blockage in the system. The low side sensor may not be engaging the compressor clutch. The compressor clutch may be defective. You may have too much refrigerant, which causes sensors in the system to shut down the compressor. You may not have sufficient airflow through the condenser (usually due to bent fins).
Have a marlin 32-20 pump octagon barrel wondering how old is it and appx value?
If you can identify the model number and serial number,then we will be able to date your marlin and help with the value if you include the overall condition of your rifle.
How do you identify opposite and absolute value of a rational number?
how do you identify opposite and absolute value of a rational number
How do you identify a gun by serial number?
It would be almost impossible to identify a gun just by its serial number.
Identify number as prime composite or neither 77?
Identify each number as prime, composite or neither: 1
What is the capacity of one number to be divided by another number called?
The capacity of one numberto be exactly divided by another number is called?????
