A condenser boiler has a primary and a secondary heat exchanger. Fuel that is used to simply warm up water can be sent to the secondary heat exchanger and reused. This is a substantially more efficient use of energy.
the work of the condensor is to condense the hot steam and change its state so that it can be used again in boiler
A flow diagram of a steam condenser typically illustrates the process of condensing steam into water for reuse in a steam cycle. The diagram shows steam entering the condenser, where it comes into contact with cooling water, leading to heat exchange that cools the steam. As the steam condenses, it transforms into liquid water, which is then collected and often pumped back into the boiler. The cooling water, having absorbed the heat, is usually expelled or recycled back to a cooling system.
gland condenser is a type of condenser in which steam which is coming from d turbine is used for the heating of demineralised water and then this water is sent to the boiler so boiling of hot water consumes less coal and thus we get benifit of it
An IK on a boiler is a Soot Blow. It is mounted on the sidewall of a boiler furnace and cleans the internal boiler parts with high pressure.
ATMOSPHERIC BOILERa boiler on which combustion air/flue gases are drawn through the boiler without a fan.(Taken directly from the Crown Boiler Co. web-site.)
In a typical steam system, steam is directed to the condenser instead of the boiler to remove heat and condense it back into water for reuse. Sending steam to the boiler would be inefficient, as it would require additional energy to convert the water back into steam again. The condenser allows for heat recovery and improves the overall efficiency of the system by recycling the condensate. This process also helps maintain optimal operating conditions and reduces water consumption.
SOUNDS LIKE YOU NEED TO PAY FOR SOME MORE OIL..CALL YOUR FRIENDLY NEIGHBORHOOD DEALER.
A Rankine cycle diagram typically shows four main components: a boiler, a turbine, a condenser, and a pump. The process involves the heating of water in the boiler to produce steam, which then expands through the turbine to generate power. The steam is then condensed back into water in the condenser before being pumped back to the boiler to repeat the cycle.
the work of the condensor is to condense the hot steam and change its state so that it can be used again in boiler
At the end of the process, the purified exhaust gasses are sent to the boiler or condenser or other equipment, or discharged into the atmosphere.
No. Exhaust steam must be condensed back into water before being pumped back to the boiler. High pressure exhaust is often used to heat production or heating equipment, returned to a condensate tank then pumped to the D/A before being returned to the boiler. Low pressure (vaccuum) exhaust is condensed by a jet condenser or shell and tube condenser before being returned to the D/A.
A condenser is a device which condenses the steam at the exhaust of turbine. Condensers are classified in to two types.Such as (1) Jet condenser (2) Surface condenser It serves important functions. Such as 1. The condenser enables the recovery and recirculation of pure feed water into the plant. Thus, (i)The cost of water softening plant is reduced and (ii) It also saves the cost of fresh water to be supplied to the boiler.
A vacuum pump is used to expel air and non-condensible gases from the condenser in order to allow it to continue accepting steam (the collapse of which produces the vacuum in a condenser). If the vacuum pump fails, it will take from seconds to a few minutes before enough non-condensible gases build up in the condenser to stop the flow of steam. The non-condensible gases come from the boiler feedwater supply, despite the fact that boiler water is treated to prevent this. The minute amount of air in the water is carried with the steam into the turbine then the condenser where it will concentrate unless removed by the vacuum pump.
The feed system cycles between boiler and turbine and enables the steam to return to the boiler as feed water. A closed feed cycles a main propulsion steam run turbine through a high pressure water tube boiler. The condenser, set to a high vacuum, will receive the steam turbine exhaust.
The feed system cycles between boiler and turbine and enables the steam to return to the boiler as feed water. A closed feed cycles a main propulsion steam run turbine through a high pressure water tube boiler. The condenser, set to a high vacuum, will receive the steam turbine exhaust.
A process called distillation would be used to separate a mixture of salt and water. Equipment such as a distillation flask, condenser, and heat source would be necessary. The mixture is heated, and the water evaporates leaving the salt behind, which can then be collected.
In a generator, the condenser serves to maintain a vacuum within the system, which helps improve the efficiency of the steam cycle. It condenses exhaust steam from the turbine back into water, allowing it to be reused in the boiler. By reducing the pressure in the condenser, it enhances the turbine’s performance and increases the overall efficiency of the power generation process. Additionally, it helps in minimizing the loss of water and supports the continuous operation of the system.