0
What else can I help you with?
The frontal area of a centrifugal compressor as compared to axial flow compressor is larger or smaller?
the frontal area of a centrifugal compresor is more as compared to axial flow compressor for a given air flow. And for this reason axial compressors are being used in aircraft engines.
Why does a longer beam length mean greater deflection?
Deflection of beam depends upon load and length of beam. Larger the beam, larger will be it's selfweight
What is the larger of the two mating gears?
The gear with the greater number of teeth; it will have a lower angular velocity .
How does a heater use a motor?
Motors in heaters are to run the fans to distribute the heat over a larger area.
Can hydraulic pumps be used as motors?
no. motors POWER hydrolic pumps. hydrolic pumps cannot function at the fast rate needed to generate energy as motors do. Answer 2 There is not necessarily any need for a hydraulic - or any other - motor to function at a fast rate, as you put it. A hydarulic pump may need to only turn at say 1 rpm and at this speed send out enough oil to drive a hydraulic motor. Then main thing to consider is what type of pump are we talking about? A gear type oil pumo my well not work at very low speeds, but a piston type pump will work very slowly if needed.
Where is the Intake Air temperature on the 2006 dodge charger daytona rt?
take a look at the intake tube (between the air box and the engine) it is the larger plug on the backside of the stock intake.
Why are intake ports on low- and medium- temperature compressors larger in size than intahe ports on air conditioning compressors?
To begin with the suction line is always larger than the discharge so it can facilitate the movement of the required volume of vapor, which because it is at a lower pressure is less dense so it needs more area (larger pipe). In a low or medium temp refrigeration system the suction pressure is lower still, so the gas is even less dense, thus even more area (larger pipe) is required. Additionally, as the design operating temp of the system is lowered so is the rated tonnage. Therefore a 20 ton freezer system will be physically larger than a 20 ton AC system.
Which valve is intake and which is exhaust?
An intake valve is larger.
What are application of rotary screw compressors?
Rotary screw compressors are used in many industrial compressed air systems due to the high volume they produce in comparison to reciprocating compressors. Rotary screws take up much less space, require no heavy flywheels, and need less maintenance than the recip. compressors. Oil free compressed air can be produced by large rotary screw compressors designed as such, while reciprocating compressors can do this only on a smaller scale due to the need for cylinder lubrication in the larger models.
Which is intake valve on Chev 350?
Intake valves are larger than exhaust valves, and are aligned with the intake runners on the intake manifold.
What does a small air compressor do?
Small air compressors are typically lighter weight and easier to transport than full size compressors. They are good for small scale use, whereas you would require a larger version to generate sufficient power to operate larger tools or for use over a long period of time.
Are some 305 intake distributor wholes larger?
no
What valve is exhaust and what valve is intake on 16HP vanguard Briggs?
The intake valve is always the larger of the two.
What engine valve is the largest?
The intake valve is usually larger.
In most engines head of the intake valve is?
the intake valve head is larger than the exhaust valve head
WHO MAKES CAMPBELL HAUSFELD AIR COMPRESSORS?
Campbell Hausfeld air compressors are manufactured by Campbell Hausfeld, a company that has been producing air compressors and related equipment since 1836. The brand is known for its wide range of air compressors, tools, and accessories designed for both consumer and industrial use. Campbell Hausfeld is based in the United States and is part of the larger group known as the "Campbell Hausfeld Group," which focuses on providing quality products for various applications.
Where is temp sensor in a 94 ford v6?
The coolant temperature sending unit for your engine temperature gauge is located on the intake manifold just to the left of the thermostat housing ( when looking from the front of the Explorer ) The larger sending unit to the right of the thermostat housing is for the EEC - IV system
