0
What else can I help you with?
What is the use of channel lock pliers?
Channel lock pliers are very versatile. My main use of them is for holding large and awkwardly sized objects, for instance, clearance trap nuts under sinks.
What is the use of gully trap in drainage system?
Gully Trap will prevent the back flow and stop Foul smell developed by means of all the waste point collection.
What is the Machining operation that uses a toothed cutting tool to produce shapes inside of a hole?
counter-bore chamfer counter-sink
What is pressure flow?
The pressure flow theory describes the movement of food through the phloem. The theory was originated by Ernst Munch.
What type of simple machines-gears can you find in a kitchen?
knife, bottle cap, broom, mop, sink handle, sink, oven door, fridge door, can opener, cheese grater, blinds, pizza cutter
Is your sink trap leaking and in need of repair?
Is your sink trap leaking and needs fixing?
Can you use the existing shower drain for a pedestal sink and do you need a trap for the sink since there is already a trap in the floor?
No and yes. Amendment (not from a professional plumber!): If you were simply running the sink drain into the shower drain and if there was not a reduction in pipe size, I would think you would be able to do that. I think the reason you need a trap for the sink has to do with code that requires a trap be no more than 24" from the basin to the trap arm. That being said, the pedestal sink in my house does not have a trap until after it drains below the floor.
Minimum distance below sink to trap?
What is the minimum distance between the bottom of a sink and the trap attachment for a bathroom sink
How do you install pipe without p-trap?
You need aP-trap under every sink. Get a plumber if you don't know what you are doing.
What are the different parts of a sink trap?
A sink trap typically consists of three main parts: the U-shaped trap bend, the trap arm, and the trap adapter. The U-shaped trap bend holds water to prevent sewer gases from entering the house. The trap arm connects the trap bend to the drain pipe, and the trap adapter connects the trap to the sink's tailpiece.
What are the steps to properly install a p-trap assembly in a sink?
To properly install a p-trap assembly in a sink, follow these steps: Remove the existing p-trap assembly, if applicable. Place the new p-trap under the sink drain. Connect the trap arm to the sink drain and the trap bend to the trap arm. Tighten the slip nuts with pliers to secure the connections. Check for leaks by running water through the sink. Make adjustments if needed to ensure a proper seal. Test the sink again to confirm the p-trap is installed correctly.
Do you need a air vent for the dishwasher in California?
It is usually hooked up to your kitchen sink p-trap or garburator under the sink, which is vented. This is the only vent you need for drainage.
How can I create a flexible trap for my sink?
To create a flexible trap for your sink, you can use a P-trap with adjustable joints that can be easily adjusted to fit the specific dimensions of your sink. This will allow for flexibility in installation and maintenance.
When adding a new sink can you use a vent pipe that another sink is already using?
You need to check with your local and state building codes, but I have done this many times before. Just make sure that it is utalizing a trap. If you go into the other drain below the other trap make sure you plumb in a new trap for the new sink
How do you install a P-trap under a sink?
To install a P-trap under a sink, first, remove the existing trap. Then, connect the new P-trap to the sink drain and the wall pipe using slip-joint nuts and washers. Make sure the trap is properly aligned and secure all connections. Finally, check for leaks by running water through the sink.
How to properly plumb a bathroom sink?
To properly plumb a bathroom sink, you will need to connect the sink's drain pipe to the main drain line using a P-trap. The P-trap helps prevent sewer gases from entering the bathroom. Make sure to secure all connections tightly and test for leaks before using the sink.
When was the sink trap invented?
1743 in England for the Duke of York and if you need the exact month check out the history of plumbing
