0
there are two inserts with lines on - one on each side of the spool just grab a hold with thumb and forefinger and press and pull shud come out quite easy now a question for u lol how do u set new one up to put in there are two notches and one hole either side were does the line go thanx
What else can I help you with?
How do you fill flymo strimmer spool?
To fill a Flymo strimmer spool, first, remove the spool from the strimmer by pressing the tabs or unscrewing it, depending on the model. Next, take the appropriate length of trimmer line (usually specified in the user manual) and insert one end into the spool's designated slot, then wind the line around the spool in the direction indicated by the arrows. Leave some line free at the end, then secure it by slotting it into the spool's holding notches. Finally, reattach the spool to the strimmer and ensure it is locked in place.
Black and decker grass hog manual?
The Black and Decker grass hog manual can be received from the Black and Decker Company. You can call the Black and Decker hotline to request one.
How to spool Black and Decker grasshog weed trimmer?
To spool a Black and Decker Grasshog weed trimmer, first, unplug the trimmer for safety. Open the spool cover by pressing the tabs or using a screwdriver, then remove the empty spool. Take a new spool of trimmer line, thread the line through the eyelet and wind it around the spool in the direction indicated by the arrows, leaving a few inches free. Finally, reinsert the spool into the trimmer, pull the line through the exit port, and close the spool cover securely.
How do you rethread a double strimmer?
To rethread a double strimmer, first, ensure the strimmer is turned off and unplugged. Remove the spool from the trimmer head by pressing the release tabs and pulling it out. Cut a length of trimmer line, typically around 20-25 feet, and thread it through the spool's holes, winding it evenly in the designated direction. Finally, replace the spool back into the trimmer head, ensuring the line is properly fed through the exit holes, and you're ready to go.
How do you extend cutting cord on ryobi strimmer?
To extend the cutting cord on a Ryobi strimmer, first ensure the strimmer is turned off and unplugged for safety. Locate the spool cover and remove it by pressing the tabs or unscrewing it, depending on the model. Then, pull out the existing cord, and if needed, feed new cutting line through the spool according to the manufacturer's specifications, winding it in the correct direction. Finally, reattach the spool cover and trim any excess line to the desired length.
Which trimmer has the best system for changing the string?
Black & Decker's Automatic Feed System is the best for advancing the string.The Poulan Pro Spool is best spool if you have a low tolerance for nuisance in changing and untangling.
What is bump feed on grass strimmer?
Bump feed on a grass strimmer refers to a mechanism that allows the user to release more cutting line by tapping the strimmer head against the ground while operating it. This action causes a spool inside the head to advance the line, providing a fresh length for cutting without the need to stop and manually adjust the line. It enhances efficiency and convenience, making it easier to maintain a consistent cutting performance.
What is a spool pin?
Spool pins are used on sewing machines to hold the spool of thread. Most or vertical, some that are horizontal use a spool cap to secure the spool of thread. Some machine come with spool nets to cover the spool to ensure the thread enter the machine evenly. Some machines come with an extra spool pin that fits into a small hole on the top of the machine to hold a second spool of thread.
How much is a spool of tread?
A spool of thread is very cheap. Spools of thread can be as cheap as a dollar or less a spool.
What do you call a genuine spool?
A real reel is a genuine spool.
When was Emma Spool created?
Emma Spool was created in 1982.
What is spool in a sentence?
That spool is just the right size for my project.
