answersLogoWhite

0

On the fan pulley...

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do you remove the fan clutch to get to the water pump on a Ford Aerostar?

Not all the fan clutch nuts are left hand thread some are right handed. It states which type you have on the top of the radiator shroud.AnswerPut a rag on the pulley and wrap your chain wrench around it to hold on and keep the pump from turning when you put your monster adjustable wrench on the clutch and turn it off. Sears sells a strap wrench (Part #45570) that works really well for holding the fan pulley.


How to remove the fan drive on a 1997 dodge van 318 5.2 v8?

Remove the fan shrouds (3/8" and 7/16" bolts), and rent a Clutch Fan Removal Tool from Autozone / Advance Auto Parts / O'Reilly. One wrench holds the pulley in place using the bolts, another cranks the fan. If you don't have access to an auto parts store, or it's rented out already... Get a vice grip. Put it on a water pump pulley bolt. Put a long pipe on the wrench's handle, and rotate it until it hits the ground. Now grab a channelocks and break free the fan, using the wrench/pipe/ground to hold the pulley in place.


You are replacing the water pump on your 1994 Safari everything was going fine until you got to the fan you got the 4 nuts off but the fan clutch won't come off any suggestions No other bolts?

you need to put the 4 bolts back in the pulley there are four little holes in the pulley were a special holding tool goes then put a wrench on the clutch and loosen, some of them fans had reverse threads so be careful. hope this helps you!


Which way do you turn the nut on a coolant fan for a 98 gmc sierra?

GM in there infinite wisdom has a specialty wrench for that to hold the pulley while you turn the nut counter clockwise while facing the engine. The specialty wrench is a flat bar about 1-1/4 by 1/8 thick and 12 inches or so long. It has two holes on one end which are 1-7/8" apart and 3/8"diameter. There is an arch cut between the two holes to allow clearance for the fan clutch nut. To use it you remove two of the four bolts that holds the pulley to the water pump and bolt the wrench to the pulley with the bolts you removed. Leaving the fan belt on, should provide enough friction for removal. This will allow you to hold the pulley while removing the nut turning counter clockwise while holding the fan pulley with the specialty wrench. You may have some luck without the specialty wrench, if you leave the belt on and have a large enough wrench you can put it on the fan clutch nut and tap it with a mallet counter clockwise. I looked up the specialty wrench on the Internet, and once I saw it, I had it made in a matter of 15 minutes. Some chain auto parts stores rent tools. When you see the yoke under the pulley, you'll wonder why they did it that way and not just use a simple bolt on connection for the fan clutch rather than that big nut.


Is there a special tool required to remove the cooling fan on a 1997 jimmy?

No, there is no special tool. The bolt that holds the fan clutch on is a reverse thread. Once that is removed, along with the fan blades, you can remove the fan by unbolting it from the fan clutch. I had a miserable time getting my fan off of the car. What a local mechanic told me, which is what I did, was put a wrench on the nut and smack it with a hammer until it loosens up. Remember to whack it to the right because of the reverse threading! Hope that helps, Mr_Dog A strap wrench will assist in holding the pulley stationary while trying to break the nut loose.


How do you put on alternator belt on 90 Honda civic?

You need to line up you belt with the pulley except for the tensioner pulley according to the picture in your engine bay. You will need to put a wrench on your tensioner pulley and twist it to relieve the tension then slip the belt on and let off the wrench to return the tension.


Do you have to put the tensioner pulley on before installing the serpentine belt on a 94 Isuzu Rodeo or is it possible to install it last?

its easier to put the pulley on first, then thread the belt up to the pulley then use a wrench to pull against the spring on the pulley, then slide the belt in. using a 15mm wrench on the bolt or an Allen will give you all the leverage you need for an easy install


How do you install fan belts on a 92 landcruiser?

Put the new fan belts around the fan pulleys. Slide the top tensioner pulley upward. Tighten down the tensioner pulley when you have achieved the proper fan belt tension.


How can you get the wrench in Club Penguin?

To get the wrench you click the little light on your spy phone and a wrench, a comb, and scissors pop out. Then you click the wrench to take it. To put it away simply click the spy phone while holding the wrench.


How do you remove fan from water pump in 94 dodge 1 ton van?

Go to your local Advance Auto Parts / Autozone / O'Reilly and ask for the Clutch Fan Removal Tool. You will need to put down a deposit, but you get it back in full when you return the tool. There's a large wrench that goes around all 4 pulley bolts and holds them in place while you use the other wrench to break loose the fan.


How do you release the tensioner to put belt back around the alternator?

This is easiest done with 2 people. Put the belt around everything but the alternator. On the tensioner pulley or the base of it, there should be a box or something that will fit a wrench. Get that wrench, and another of a similar size (you will probably have to do the 2 wrench trick to extend your wrench distance to be able to move the pulley). Push or pull (depending on car, try the other if the first didn't work) on the wrenches and you will notice the belt moved a little bit. Push/pull as necessary to "make it long enough" to fit around the alternator pulley. Put the belt around the alternator pulley, remove the wrenches, and inspect the belt to make sure it's on every pulley properly. you don't want it hanging off the side of a pulley.


How do you install fan belt on 1997 ford ranger 3.0 v6?

Loosen the tensioner pulley. Put the fan belt around the pulleys. Pry the tensioner pulley to the right until the belt is tight. Tighten the tensioner pulley nut.