0
What else can I help you with?
What spark plug for stihl 024 chainsaw?
The correct spark plug for a Stihl 024 is an RCJ6Y (Champion), BPMR7A (NGK), or a WSR6F (Bosch). Make sure that the gap is set to 0.020 inches.
How do you set the carb on a stihl 025 chainsaw?
To set the carburetor on a Stihl 025 chainsaw, first ensure the chainsaw is off and cool. Locate the adjustment screws, typically labeled L (low speed), H (high speed), and T (idle). Start the chainsaw and let it warm up, then adjust the L screw for optimal idle speed and smooth acceleration, followed by the H screw for maximum power at full throttle. Finally, adjust the T screw for a stable idle, ensuring the chain does not move when idling.
How do you service your stihl saw carburetor?
Chainsaw carbs are very picky and have to be set just right. As you are obviously not familiar with them, you should take it to you local lawnmower and small engine shop.
How do you start a stihl ms187 chainsaw?
To start a Stihl MS 187 chainsaw, first ensure the chain brake is engaged. Then, set the ignition switch to the "On" position, pump the primer bulb until fuel is visible, and pull the choke lever to the closed position. Place the chainsaw on the ground, press the throttle trigger, and pull the starter rope until the engine fires. Once it starts, open the choke and allow the engine to warm up before use.
What is the ignition coil gap for a Stihl 024 chainsaw?
The ignition coil gap for a Stihl 024 chainsaw is typically set to around 0.2 mm (0.008 inches). This gap ensures proper spark generation for efficient engine performance. It's important to use a feeler gauge to accurately measure the gap when adjusting. Always refer to the owner's manual for specific guidance on your model.
What is the ignition coil gap for a stihl ms250 chainsaw?
The ignition coil gap for a Stihl MS250 chainsaw is typically set to approximately 0.2 mm (0.008 inches). This gap ensures proper spark generation for efficient engine performance. It's important to check the gap periodically and adjust it if necessary during maintenance. Always refer to the owner's manual for specific recommendations and guidelines.
What is the spark plug gap for a ms460 stihl chainsaw?
The spark plug gap for a Stihl MS460 chainsaw is typically set at 0.020 to 0.025 inches (0.5 to 0.65 mm). It's important to check the owner's manual for specific recommendations, as variations may exist based on the model or production year. Proper gap settings ensure optimal engine performance and efficiency.
What needs to be changed to go from points to an electronic ignition on a stihl 031AV chainsaw?
You can use the same flywheel but need to put in a complete solid state ignition set up. http://store.chainsawr.com/
How do you adjust timing on 025 stihl chainsaw?
To adjust the timing on a Stihl 025 chainsaw, you typically need to check the ignition timing, which is usually set at the factory. If you're experiencing issues, first ensure the flywheel and ignition module are clean and properly secured. For more precise adjustments, consult the service manual for specific timing specifications and use a timing light if necessary. If you're unsure, it's best to seek assistance from a professional technician.
What are the carb settings on a ms 210 stihl?
The carburetor settings on a Stihl MS 210 chainsaw typically involve adjusting the L (low speed) and H (high speed) screws for optimal performance. The L screw is generally set to allow for a smooth idle and acceleration, while the H screw controls the maximum speed under load. It’s important to refer to the user manual for specific settings, as they can vary based on the saw's condition and altitude. Always ensure the chainsaw is tuned correctly for safety and efficiency.
How do you start a stihl 041 AV?
To start a Stihl 041 AV chainsaw, first ensure the chain brake is engaged and the fuel mixture is prepared. Set the choke to the "cold start" position, pull the starter cord until you hear a pop or see signs of firing. Then set the choke to the "run" position and pull the starter cord again until the engine starts. Once running, disengage the chain brake and allow the saw to warm up.
How do you change the pull cord on a stihl chainsaw?
hi to change the cord on a still saw is abit tricky as there is coil spring in side you have to set it up so that when pulled it will recoil its self take it to atool hire shop they will sort it in 1hr at a price of £10-£15 POUNDS no hasstle
