answersLogoWhite

0

On a 1998 Harley-Davidson XL1200C, the ignition module is typically located under the seat. To access it, you'll need to remove the seat, and you may also need to remove the side cover to reach the module. It's usually mounted on the frame or near the battery area. Always consult the service manual for specific instructions and safety precautions.

User Avatar

AnswerBot

1w ago

What else can I help you with?

Related Questions

Where is the ignition module on a 1999 4 cylinder Chevy S 10?

The 1999 Chevy S 10 pickup truck ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


How do you change the Ignition Control Module in a 1995 Blazer S-10?

Remove the wiring harness from your 1995 Chevy Blazer ignition control module. Remove the ignition control module retaining screws. Reverse the process to install your new ignition control module.


Where is the ignition control module located on a 1992 Chevy S-10 Pickup?

The Distributer module on "92" S-10 Vin code "W" or "Z" is located on the distributer,you must remove the distributer cap to gain access to the ignition module. Once you have gained access to the ignition rotor it is always necessary to always test the module before replacing it.


Where is the ignition control module on 93 olds cutlass cierra s with 3300 V-6?

The ignition module on a 86 ciara 2.5 is located under hood, center,lower engine area,below driver side of intake manifold . mounted inside of distributor


Where is the ignition coil on a 2001 Chevy S-10 2.2 l?

The ignition module and coils are located on the lower passenger side of engine block. It is best to access from underneath.


Why do you lose power when taking off on your 96 s-10 blazer?

Could be a bad fuel filter or ignition coil/module.


Where is the electronic ignition module located on a 1995 ford mustang gt?

on 1994-95 Mustang v-8's the module is located on the passenger side fenderwell in front of the shock tower.


How do you check ignition control module on 93 s 10?

Diagnosing the ignition control module is done with a diagnostic scope. These scopes can range in cost from a few hundred dollars to several thousand, so the most economic way is to take the car to an auto repair shop.


No power to fuel injectors on 1987 Chevy S 10?

Replace you ignition module, It controls both spark and power to the injectors. You can have spark but the module may be bad and not giving power to the injectors and the vehicle will not run.


Can I run the screaming eagle ignition module 32750 99c on my carbureted 2000 dyna with s e heads and s and s 210 gear driven cams?

Yes, you can run the Screaming Eagle Ignition Module 32750-99C on your carbureted 2000 Dyna equipped with Screaming Eagle heads and S&S 210 gear-driven cams. This ignition module is designed to enhance performance and is compatible with modified engines. However, ensure that your bike's overall setup, including carburetion and timing, is properly tuned to maximize performance and reliability. It's always a good idea to consult with a professional mechanic or tuner for specific compatibility and tuning advice.


2001 S-10 4.3 vortech V6 truck will turn over but not start im gettin fuel and spark to the engine?

ignition control module


Cam sensor in 97 s series Saturn?

No such thing exists on a 91-02 Saturn s-series. The above is correct... mostly. Saturn did not use a physical camshaft positioning sensor on any of its S-series vehicles. There is however a pseudo camshaft pulse generated by the ignition control module and sent to the computer. If you are receiving faulty cam position sensor trouble codes, the problem exists in the Ignition control module.