0
What else can I help you with?
How much oil do i put a in Suzuki lt160?
Our Suzuki LT160 is a 1998 and it takes a quart and a half.
How do you clean a carburetor on a 1989 suzuki lt160 ATV?
will your 4wheeler tend to stoll after pushen the coutch to far on it?
Will a Suzuki 185 interchange with a Suzuki lt160 ATV?
Well, friend, when it comes to swapping parts between different models, it's important to check if they are compatible. I recommend looking at the specifications and doing some research to see if the Suzuki 185 engine will fit in the Suzuki lt160 ATV. Remember, with a little patience and creativity, you can make things work beautifully.
How to take off mower blades on lt160 automatic john deer?
The manual for the LT160 is still available online. Check the link below.
Will hood for LT155 fit a LT160?
Yes.
What other cdi box will work on a suzuki lt125?
For a Suzuki LT125, you can consider using a CDI box from similar models like the Suzuki LT80 or LT160, as they may have compatible electrical systems. It's important to ensure that the CDI box matches the specifications for your particular model year and configuration. Always double-check with a mechanic or parts specialist to confirm compatibility before making a purchase.
How much oil does lt160 take?
The LT160, a model from Metso's mobile crushing and screening equipment, typically requires around 10,000 liters (approximately 2,641 gallons) of oil for its lubrication system. However, the exact amount can vary based on the specific configuration and operational conditions. Always refer to the manufacturer's manual for the precise specifications and maintenance guidelines.
I need a mower belt diagram for a John Deere 110?
The John Deere LA130 is a model of riding lawnmower produced by the John Deere Company. The mower uses a 48 inch mower belt. Replacement mower belts are available online and at specific retailers.
Suzuki lt160 1990 the starter is just free spinning it is not turning the motor over what do you do?
sounds like the ring gear or flywheel is worn if you have a manual or stick shift put it in 2nd gear depress clutch let car roll a little release clutch (the engine will turn slightly) then try starting engine. with auto transmission you will have to turn engine over with socket and ratchet bar (if you cant turn over at the drive belt by hand) if this starts your car the flywheel will need replacing... Could also be the bendix ... the solenoid that engages the starter motor to the flywheel.
How do you adjust the clutch on a suzuki lt160?
Remove the cap where you see the oil level in a little windows(3bolt).On the right side of the engine. Then you see a bolt with a groove to be turned by a screwdriver's bolt is locked by a nut's that's your adjustment (the one upper). Loose the nut the be able to turn the bolt. Turn the bolt with a screw driver counter clockwise to tighten the thing.1/8of a turn at the time or check by moving the gears selector pedal just to let a little free play to the adjustment bolt to move because if its to tight the clutch gonna slip. Tighten the lock nut an ensure that the bolt is not turning. I'm bad in English lolRead more: How_do_you_adjust_the_clutch_on_a_Suzuki_LT_160
How do you replace the drive belt on a John Deere L100 Lawn tractor?
You must back out three bolts which hold plastic cover over left side spindle pulley first. After cover is removed (or at least two rear bolts are removed allowing cover to be pulled up ) work belt onto this pulley and reinstall bolts on cover. Then, you must loosen idler pulley next to pulley you just placed belt on as to thread belt onto idler pulley which has a metal fence mounted on pulley shaft to keep belt on this idler. Belt must then be threaded around on/off pulley and right spindle pulley and drive pulley.
