answersLogoWhite

0

Each region of the neuron contains distinct membrane proteins that provide the basis for the threshold differences.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Movies & Television

Are all voltages in a circuit referenced to ground?

Typically yes, but not always: you can also measure the voltage between any two points in a circuit to determine the voltage difference between those two points. It all depends what you are trying to find out about the circuit.Another example of a voltage that is not referenced to ground is the phase-to-phase voltage in a 3-phase electrical service.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


What is the relationship between RMS and peak voltage for a square waveform?

RMS and peak voltage for a square waveform are the same. There is a small caveat, and that is that you'd have to have a "perfect" square wave with a rise time of zero. Let's have a look. If we have a perfect square wave, it has a positive peak and a negative peak (naturally). And if the transition from one peak to the other can be made in zero time, then the voltage of the waveform will always be at the positive or the negative peak. That means it will always be at its maximum, and the effective value (which is what RMS or root mean square is - it's the DC equivalent or the "area under the curve of the waveform") will be exactly what the peak value is. It's a slam dunk. If we have a (perfect) square wave of 100 volts peak, it will always be at positive or negative 100 volts. As RMS is the DC equivalent, or is the "heating value for a purely resistive load" on the voltage source, the voltage will always be 100 volts (either + or -), and the resistive load will always be driven by 100 volts. Piece of cake.


Which increases or decreases the voltage of alternating current?

(i) EMF (Electro Motive Force) the source of voltage can increase or decrease voltage. (ii) Load connected can increase or decrease voltage (In case of overload voltage reduces.) (iii) Resistance of wire - I R loss ( Voltage drop V = IR)


What is the same in a parallel circuit?

Always voltage constant in parallel circuit if you look your house wiring all are in parallel therefore 220 volt present in every house but current is different


What is the volt drop across a 10k resistor with a 5 volt supply?

If there is nothing else in the circuit, then the voltage drop across the resistor will be the full supply voltage of 5 volts. The size of the resistor does not matter in this case - it will always be 5 volts.

Related Questions

Why is voltage always measured between two points?

Voltage is always measured between two points because it represents the difference in electric potential between those two points. This difference in potential is what drives the flow of electric current in a circuit.


Why peak voltage of the load is smaller than the voltage from the transformer output?

The voltage appearing across a load is always smaller than the no-load voltage of any voltage source -e.g. batteries, generators, or transformers. In simple terms this is because all these voltage sources have internal resistance or impedance which results in an internal voltage drop when the source delivers a load current. The resulting voltage, therefore, is always the difference between the no-load voltage and the internal voltage drop. A measure of the difference between a source's no-load and full-load voltage is termed its 'voltage regulation'.


What is meant by lead and lag?

The terms, 'lagging' and 'leading', describe the relationship between a circuit's load current and supply voltage. They describe whether the load current waveform is leading or lagging the supply voltage -always the current, never the voltage. Inductive loads always cause the current to lag the supply voltage, whereas capacitive loads always cause the current to lead the supply voltage.


What is meant by lagging and leading circuit?

The terms, 'lagging' and 'leading', describe the relationship between a circuit's load current and supply voltage. They describe whether the load current waveform is leading or lagging the supply voltage -always the current, never the voltage. Inductive loads always cause the current to lag the supply voltage, whereas capacitive loads always cause the current to lead the supply voltage.


Does voltage flow in a circuit Explain?

Voltage in an electrical circuit is the rough equivalent of pressure in a water pipe. It causes the electricity to flow. Higher voltage; more flow. The difference is that you can think of pressure applied at a single point, but voltage is always the difference in electrical potential between two points. That's how a bird can stand on a 7,000-volt rural electrical line without harm. The potential difference (voltage) between the line and the ground is 7,000 volts, but the potential difference (voltage) between the bird's two feet is very tiny.


What is maximum safe voltage for portable electrical tools?

There's no set answer to that, it's always a tradeoff between how well insulated the tool is, and what voltage it uses.


How do you explain why a square is always symmetric?

explain why a square i always symetric


How do you wire a 110 V DB board from a 220 V 3 phase transformer supply?

In a wye system the voltage between any two wires will always give the same amount of voltage on a three phase system. However, the voltage between any one of the phase conductors (X1, X2, X3) and the neutral (X0) will be less than the power conductors. For example, if the voltage between the power conductors of any two phases of a three wire system is 220v, then the voltage from any phase conductor to ground will be 110v. This is due to the square root of three phase power. In a wye system, the voltage between any two power conductors will always be 1.732 (which is the square root of 3) times the voltage between the neutral and any one of the power phase conductors. The phase-to-ground voltage can be found by dividing the phase-to-phase voltage by 1.732 answer from ground and any phase


What is the difference between voltage restrained overcurrent protection and voltage controlled overcurrent protection?

Voltage restrained overcurrent protection uses a fixed voltage threshold to trip the protection device when an overcurrent condition is detected. In contrast, voltage controlled overcurrent protection adjusts the trip threshold based on the system voltage level, allowing for more precise coordination with other protective devices and better protection of the equipment. The key distinction lies in the method of setting the trip threshold: fixed voltage for voltage restrained, and voltage-dependent for voltage controlled overcurrent protection.


What is the voltage used for an iPod dock station?

The voltage use in an iPod dick station is between 5v and 12v. This is a normal voltage use for a small appliance. Saving energy is always important so all plugs should be unplugged when not in use.


Were do you buy a voltage amplifier?

In audio look at an amplifier. It will be always a voltage amplifier.


What type of signal at the NPN output?

A: It always a voltage since it is a voltage amplifier