0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How much does one pump of grease weigh from a grease gun?
In a pistol grip grease gun each pump weighs 33 grams.
What equipments are used for wellhead maintenance?
General equipment are : Hydraulic tool to open and tight studs, grease pump, stinger to check pressure in the cavities, VR plug lubricator, BPV lubricator, air compressor, heavy grease hand pump, hand pump, BPV, TWCV. Grease, Ring gaskets, bearing grease pump ...
What is a grease fitting?
a grease fitting is something that u put a grease gun into and pump grease into it to lubricate ball joints, steering knuckles ect...
How do you prime a 2.2 Toyota Camry oil pump?
many engine builders like to use lubriplate 105 assembly grease pack clean grease into inlet of pump for start up or if pump is open pack clean grease into gears or lobe and rotor
Why did they nickname the M3 machin gun the Grease Gun?
It has a superficial appearance similar to the tool that was used by mechanics to pump grease into fittings on cars, and that tool is called a grease gun.
How do you change the fuel pump in a 327 Chevy Small block Think it is 1968?
it is located on right front of block. First remove your fuel lines, the remove the retaining bolts holding it on the pin will slide out after the pump. coate the pin with grease and reinstall in its hole(grease will hold it for you so you can get the pump in) the install pump and lines
How do you remove large quantities of grease from grease trap drain?
Mechanically: scoop it up into a bucket. If it is liquid you can pump it but if it too thick then you got to shovel it out.
When changing the fule pump on an 1983 Chevy 350 what about the push rod that runs the pump will it fall out and is there any way to hold it in place?
You can put grease on the rod and gently push it into the block. the grease will hold it in place for a good amount of time.
How do you install 86 gmc truck fuel pump?
i have an 86 gmc and the pump is on the right side of the block and it runs off the cam. it has three ports on it. if it is mechanical then when replacing it you should slide the pump down and in, so the pushrod is resting on the pumps lever. a good trick for getting the pump in below the push rod is to use axle grease. coat the rod in a generous amount so that the grease sticks the rod in place, holding the rod up and out of the way as you install the pump. It is best to have to engine as cool as possible with this or the grease won't hold as well.
Why does Hand grease gun loses its prime?
Grease is too thick to get all the air bubbles out during manufacture and packaging. The grease gun pump is designed to move thick liquid (grease). When a large air bubble gets into the grease gun's piston cylinder, your grease gun is now one of the world's smallest and most inefficient air pump. The remedy for this problem is the little button on the front cap of the grease gun next to the handle pivot or piston. It takes much more air pressure than the grease gun's piston and cylinder can create to move any grease with this small air bubble. Just imagine squeezing a car tire to the size of a doughnut with out popping it. Relieve the pressure of this air bubble and now you can vacuum in some grease behind it with the grease gun's piston and cylinder repriming the grease gun. Long answer short: airbubble.
How do you change a fuel pump on a 1971 fury?
take fuel lines off the pump and then remove the 2 bolts holding it on then pull it off, to install new pump there is a rod inside the engine that has to be pushed up while you slide the new pump in, I get a glob of grease and push the rod up and put a glob of grease on the bottom of the rod to hold it up in place so I can get the new pump in and get both bolts started and then tightened, re-hook fuel lines to new pump and your done.
How do you install a fuel pump on a 1966 Chevy Malibu?
unhook all fuel lines to the pump and then there are 2 bolts that hold it onto the engine, remove the bolts and the pump is off, scrape old gasket off block and install new gasket onto new fuel pump, now stick a glob of grease on you finger and inside the fuel pump hole on the engine there is a rod that has to be pushed upward so you can get the new pump into position to bolt up, take that glob of grease on your finger and push that rod upward with that glob of grease on the end of the rod to hold it upward long enough for you to get the pump bolted into place, tighten the 2 bolts and hook up all fuel lines and your done.
