If your not interested in safety or wiring codes use the formula. E x I = Va(Watts without knowing Power Factor.) E is your voltage at the source (Breaker) 110v, 115v, 117v. I is 15amp the breaker is rated for.
X is your number of bulbs.
example. 110 x 15 = 60X : 60x = 1650 : 1650/60 = X Please do not attempt doing this hookup. % If your not interested in safety or wiring codes use the formula. E x I = Va(Watts without knowing Power Factor.) E is your voltage at the source (Breaker) 110v, 115v, 117v. I is 15amp the breaker is rated for.
X is your number of bulbs.
example. 110 x 15 = 60X : 60x = 1650 : 1650/60 = X Please do not attempt doing this hookup.
60
W=VE
watts = volts x amps (current)
= 120 x 30
3600
3600/60 watts per bulb
60 bulbs
The series circuit has one wire, while the parallel circuit has two wires. And if you connect the extra wire its dim because your taking away electrons and energy flowing through the main circuit -Hope this helped:D The difference is that series circuit has one path but parallel has more than one path. -hope this helped!:D ~Bunnii Boo
Arrange the light bulbs in parallel with a swith between them. Like in the (simple) diagram below _____________/ ____________ | | | | | | | | | | | | _ O O - | | | | | | | | ------------------------------------------ I hope this helps :-) ---- Visualize two parallel lines like a ladder. One is the "hot" line and the other is the neutral. Now visualize the cross rungs in the ladder. These will be the loads on the circuit. Go from the "hot side of the ladder through a switch and through a light bulb to the neutral side of the ladder. Go up one rung on the ladder and add another switch and light bulb. Go up one more rung and connect a receptacle from the "hot" side of the ladder to the neutral side of the ladder. This is how house circuits are wired on each breaker circuit. This circuit could be for one room only. Another circuit could be wired for another room , and so on. As you can visualize turning the light off and on does not effect any of the other devices connected to the same circuit.
In a parallel circuit, more power is provided to the lights. Power = V2/R . The resultant resistance of the circuit is lower, and the potential difference is not divided as in a circuit in series. Thus, lights in parallel burn brighter.Additional InformationA lamp's power rating only applies at its rated voltage. Because the voltage across each branch of a parallel circuit is the same, each lamp can be supplied with its rated voltage and, therefore, will operate its rated power. In a series circuit, the voltage appearing across each lamp will be considerably lower and, so, the lamps will not operate at their rated powers.
The switch will not increase the current. The only thing that will increase the current is adding a larger load.Another AnswerTo maximize current flow in a circuit with 2 Flashlightbatteries, 2 Flashlight bulbs, and a switch, set aside the bulbs, put the batteries in series, connect the switch between the end poles of the battery set, and close the switch. The batteries will get hot and probably leak electrolyte, and be drained in seconds.If you want to maximize current through the circuit withthe bulbs in it, connect the bulbs in parallel to each other, and in series with the switch.
That is correct, but using the term parallel is an overly confusing way of saying it. - You should connect positive to positive and negative to negative. This will retain voltage and increase capacity. If you confuse the term 'parallel' with 'serial' and connect them positive to negative and negative to positive, you'd double the voltage and probably kill most if not all of the electronics in both cars.
No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.
Connect to the circuit neutral wire which should also be white.
how to connect cables to switches 240 box
You connect them in parallel.
In a circuit, either in Parallel or in Series with other components.
This is a short circuit which will create sparks. The breaker or fuse on the circuit will likely trip or blow.
The connection blades and how they connect into the distribution panel's bus.
The answer to the first part of your question is yes but the wire size has to be of a size specified in the electrical code for wires connected in parallel. As for the second part of the question the total current output is governed by the current draw of the load. It is the load current that governs the parallel wire size and the trip capacity of the breaker.
To design a circuit so that lights can be turned on and off separately, we connect the circuit in parallel.
To be short...Yes
The code says one wire per one terminal.
http://www.kpsec.freeuk.com/seriespa.htm