A Resistor does exactly what the name suggests, it creates resistance.
More precisely, it creates resistance for the flow of electrons, effectively limiting the amount of current flowing through it(and via ohms law, limits voltage).
To answer the question, A resistor isn't an input or output device, it behaves the same way no matter how you turn it and it can be placed on the input of a component(or circuit) aswell as the output.
Where is this capacitor in the circuit?A capacitor across the emitter bias resistor actually increases the AC gain because it bypasses that resistor, by increasing the ratio of collector impedance to emitter impedance which determines the amplifier voltage gain.A capacitor across the base input resistor actually increases the AC gain because it bypasses that resistor, by decreasing the attenuation of the input signal by the input circuit network.
A Resistor does exactly what the name suggests, it creates resistance. More precisely, it creates resistance for the flow of electrons, effectively limiting the amount of current flowing through it(and via ohms law, limits voltage). To answer the question, A resistor isn't an input or output device, it behaves the same way no matter how you turn it and it can be placed on the input of a component(or circuit) aswell as the output.
Typically used in logic circuits is the pull-up resistor Less common is the pull-down resistor It's purpose is to force a zero (low) value when no other component is driving the input (no load) By providing a current limited path to negative power source through the resistor, while allowing the voltage to swing high if a load is present.
what does a resistor in an ampliflyer circuit
resistor
Amplifiers comes in IC packages diagram is triangle with +/- input by adding a resistor r1 in series to the - input the gain can be found by adding a resistor from output to the - input The + terminal must be satisfied with the proper resistor
Process
If the input resistor is 3k ohms and the feedback resistor is 33k ohms in an inverting amplifier the voltage gain is -11, the ratio of 33 over 3. Consider this... The negative input terminal is a virtual ground, assuming that the positive terminal is tied to ground (usually) through a resistor. That means you have a simple voltage divider between output and input, and the output will be whatever it takes to get the common point (the negative input) to be zero. From there, its all just Ohm's law.
The series input resistor and the feedback resistor.
The emitter resistor is connected to ground(in the case of an rc coupled amplifier).Also input signal applied at the base is grounded.Then the emitter resistor forms a feedback to the input signal (through the ground return path).So emitter resistor is also called feedback resistor.
RTL logic: NPN transistor. Emitter grounded. Input connected to base through a resistor. Vcc also connected to base through a resistor. If the input is high or open, the transistor is on. If the input is low, the transistor is off. Connect a resistor from Vcc to the collector. The collector is the ouput. You have to play around with resistor values to setup your fan-in and fan-out properties.
when a resistor is connected in a circuit it drop some voltage across it.when a circuit have large input voltage then by using a resistor of suitable value we get the desired voltage.
Where is this capacitor in the circuit?A capacitor across the emitter bias resistor actually increases the AC gain because it bypasses that resistor, by increasing the ratio of collector impedance to emitter impedance which determines the amplifier voltage gain.A capacitor across the base input resistor actually increases the AC gain because it bypasses that resistor, by decreasing the attenuation of the input signal by the input circuit network.
We know definition of Resistance, that resistor always opposes to flow of current. resistor should have input signals from source , so it generates passivity in circuit
3-63A SCALING AMPLIFIER is a special type of summing amplifier with the output signaldetermined by multiplying each input signal by a different factor (determined by the ratio of the input-signal resistor and feedback resistor) and then adding these products
It depends on the shunt feedback resistor on the op-amp, for example with a 10k feedback resistor connecting the output to the inverting input, 1 mA input current gives 10 volts signal output. The input terminal stays near zero voltage because of the high open-loop gain of the op-amp, so the inverting input is termed a 'virtual earth'.
Any system you design will have an input and an output. The output will connect to the input of another system which will load it, so when you are designing any system you have to consider how loading it will effect the circuit performance.