If by power supply you mean a voltage source, it really won't matter that the resistor is removed. The voltage source will provide infinite current, instantly charging the capacitor so that the capacitor's voltage is equal to the source.
Alternative AnswerIf you are referring to an a.c. circuit, then a load current will continue to flow with its value being determined by the capacitive reactance of the circuit, and the resulting phase angle will lead the supply voltage be very close to 90 degrees.
resistor
when we replace the resistor with a capacitor ,the current will flow until the capacitor charge when capacitor will fully charged there is no current through the circuit because now capacitor will act like an open circuit. for more info plz E-mailt me at "zaib.zafar@yahoo.com"
If there are only a resistor and a capacitor in the circuit, then the phase shift will indeed be between 0 and 90 degrees. When the resistor and capacitor are in series, the phase shift will be negative when the capacitor is connected to a source voltage and the resistor is the load. The phase shift will be positive when the resistor is connected to the source. The lower the values of R and C, the higher the frequency bandwidth.With the resistor and capacitor connected in series and the two parts connected to a current source, the phase shift will be negative. At high frequencies, the output voltages is lower, and the circuit appears as a very low impedance. At low frequencies, the circuit looks more like a resistor. Again, the phase shift will be between 0 and 90 degrees.CommentThe correct term is phase angle, not 'phase shift'. By definition, the phase angle is the angle by which the load current leads or lags the supply voltage. For an RC circuit, the current leads the voltage, so the phase angle is a leading phase angle.
A fractor is a circuit component that has both the function of resistor and capacitor.
Where is this capacitor in the circuit?A capacitor across the emitter bias resistor actually increases the AC gain because it bypasses that resistor, by increasing the ratio of collector impedance to emitter impedance which determines the amplifier voltage gain.A capacitor across the base input resistor actually increases the AC gain because it bypasses that resistor, by decreasing the attenuation of the input signal by the input circuit network.
A circuit in which elements are connected in series.For example in RLC series circuit resistor,inductor and capacitor are connected in series.
The same as the time constant of a 2.7 microfarad capacitor and a 33 ohm resistor connected in series.
resistor
I wanna use resistor , capacitor and amplifier 7173 for switch alarm circuit. How can i choice resistor and capacitor value because i wanna use 24V DC.
need to use BC107 transistor which has three terminals base, collector and emitter........ collector is connected with 6.8k ohm resistor other end of this resistor is connected with 3.7 ohm resistor and it is connected to the base of the transistor which is already connected to a capacitor of 1 micro F and a positive of function generator......and in the output side i.e in the collector and emitter side connect the 1 micro F capacitor and 10 kohm resistor and connect the CRO...... then other to the ground.......
when we replace the resistor with a capacitor ,the current will flow until the capacitor charge when capacitor will fully charged there is no current through the circuit because now capacitor will act like an open circuit. for more info plz E-mailt me at "zaib.zafar@yahoo.com"
fully charged.
because without using capacitor or resistor in a circuit,it cant be complete.Resistor is used to protect the circuit by giving a certain amount of voltage.Capacitor is used to charge and discharge purpose.
R for resistor, C for capacitor. RC circuit is a circuit built with a resistor and a capacitor. This circuit will have a typical pulse response that looks like exponential decaying and a typical resonance frequency.
If there are only a resistor and a capacitor in the circuit, then the phase shift will indeed be between 0 and 90 degrees. When the resistor and capacitor are in series, the phase shift will be negative when the capacitor is connected to a source voltage and the resistor is the load. The phase shift will be positive when the resistor is connected to the source. The lower the values of R and C, the higher the frequency bandwidth.With the resistor and capacitor connected in series and the two parts connected to a current source, the phase shift will be negative. At high frequencies, the output voltages is lower, and the circuit appears as a very low impedance. At low frequencies, the circuit looks more like a resistor. Again, the phase shift will be between 0 and 90 degrees.CommentThe correct term is phase angle, not 'phase shift'. By definition, the phase angle is the angle by which the load current leads or lags the supply voltage. For an RC circuit, the current leads the voltage, so the phase angle is a leading phase angle.
The equation for such circuits is given by: V=R*I +(1/C)*Integration(idt)
A fractor is a circuit component that has both the function of resistor and capacitor.