Digital transmissions are on the TV channels 2 to 60, this is the VHF and the UHF band. Some stations changed frequencies and added new channels.
NBC, or the National Broadcasting Company, operates on various frequencies depending on the region and the specific channel. In the United States, NBC typically broadcasts its signal over-the-air on VHF or UHF frequencies, which are assigned to local affiliate stations. For example, a station might broadcast on channel 4 (VHF) or channel 11 (UHF) in different markets. Viewers can also access NBC programming through cable and satellite services, which do not rely on specific radio frequencies.
They changed back to VHF which means the bunny ears. So use Bunny ears to get channels 7.1-13.1
In the US the answer is probably not. Digital and analog TV broadcasts use the same frequencies and antennas. Digital TV is more fussy about signal quality than the older analog signals. So if you get marginal analog reception, figure on getting a new antenna for digital. The idea that there are special HDTV antennas is just marketing hype. Any antenna that gives you better digtial reception will also give you better digital reception.
VHF Chanel 16
Digital transmissions are on the TV channels 2 to 60, this is the VHF and the UHF band. Some stations changed frequencies and added new channels.
Airband, a group of frequencies in the VHF radio spectrum, uses the frequencies between 108 and 137 megahertz. A license is required to operate airband equipment.
Digital TV signals are transmitted on VHF starting on channel 2 and ending at the top of the UHF spectrum channel 69. At one time the plan was not to use the VHF band but it didn't work out that way.
The PRC77 radio operates on 30.000 to 75.95 MHz. If the Harris radio operates on any of the same frequencies (I know you said it's VHF, but VHF covers 30 to 300 MHz), then it can.
yes and also this can cause a virus n your hardware
VHF = "Very High Frequency" Formally, radio frequencies from 30 MHz to 300 MHz. (Wavelengths between 1 meter and 10 meters)
Yes
A couple of points: When you're on the receiving end, UHF signals have a few disadvantages over VHF signals, owing to UHF's higher frequencies: 1) UHF transmitters tend to be less powerful than VHF transmitters 2) Transmission lines lose appreciably more signal at UHF than VHF, and that's just for transporting the signal from the transmitter room to the antenna 3) UHF signals tend to get weaker more quickly than VHF signals as they propagate outwards from their transmitters 4) UHF receivers tend to be less sensitive than VHF receivers UHF signals have one particular advantage over VHF signals: The smaller wavelengths of UHF signals allow for a smaller antenna to provide the same performance as a larger VHF antenna. Alternately, you can make the UHF antenna larger for enhanced performance, and it might still be small compared to a nominal VHF antenna. (Please pardon all the vague, qualitative references.) High-performance antennas for UHF that are not especially huge can more-than-compensate for lower power transmitters, lossier transmission lines, higher path-losses, and less sensitive receivers. Another advantage of UHF (and microwave) is that there tend to be more frequencies available than at the lower VHF frequencies. As technology advanced over the years, radio-spectrum habitation moved from the lower frequencies to the higher frequencies. Necessarily, the tendency is for lower, "older" (VHF) frequencies to be more crowded than higher, "newer" (UHF / microwave) frequencies. More than likely, the frequency you operate on will be determined by the radio-communications-licensing authority in your country (i.e., the FCC in the USA). A particular service might have allocations available in more than one band, i.e., VHF and UHF, and then it's up to the Engineering Department to decide which of those legally available frequencies to chose for their system.
To adjust VHF (Very High Frequency) and UHF (Ultra High Frequency) radio frequencies, you typically use a tuning knob or digital interface on the radio device to select the desired frequency. Most radios have a frequency display that shows the current setting, allowing for precise adjustments. Additionally, some radios may have presets for commonly used frequencies, making it easier to switch between them. Always ensure that you are operating within the legal frequency ranges and regulations for your region.
Hi, VHF was used because primarily, that was the highest frequencies that transmitters could be manufactured for at the time TV came into existence. Since then, technoligies have improved and we've gone way, way beyond the limitations of VHF. The interesting thing is that as of February 17, 2009, ALL of the VHF TV transmitters will have been shut off (By order of Congress) and TV will have moved as an industry into all digital transmissions and HDTV. If you have an older set that's not digital ready, it'll no longer receive anything off the air. On the same token if you have a cable or satellite box currently working on your TV, you shouldn't experience any change in services. Hope this helps, Cubby
Amplitude and frequency
You need a VHF/UHF antenna (channels 2 to 60 ). Check out: http://www.fcc.gov/cgb/consumerfacts/digitaltv.html