0
What else can I help you with?
Does the glow of bulb depend on current or voltage?
Since the bulb has a constant resistance, increasing the voltage will increase the current which will increase the brightness until the bulb blows in a flash of light.Ohm's Law governs this process where Volts = Current x Resistance.Another Answer Incandescent lamps do not have a constant resistance, as their resistance increases significantly with temperature. In fact, the 'hot resistance' of a lamp filament is around 10-18 times higher than its 'cold resistance'. The temperature increase, of course, is due to the current passing through the filament. This means incandescent lamps do notobey Ohm's Law and are, thus described as being 'non-ohmic' or 'non-linear'. However, to answer your question directly, the rated power of a lamp only occurs at the lamp's ratedvoltage. Even a small reduction in voltage will result in a significant loss of power and, thus, brightness. So, in this sense, a lamp's brightness is determined by the voltage applied across its filament.
Can you use a regular bulb in a heat lamp socket?
Never put a bulb in a light socket what has a higher wattage rating than the socket. This could cause either or both of the following problems, which could result in a fire:excessive current will cause heating of the wires providing power to the socketthe higher wattage bulb will be hotter than expected and may ignite the lampshade or other parts near it
A 100w electric light bulb is connected to 200v supply calculate the current following in the bulb?
40W Bulb will spiol due to over current passing through its coilAnswerSince the 40-W lamp has a higher resistance than the 100-W lamp, the greater voltage drop will appear the 40 W lamp. As a result the 40 W lamp will be subjected to a voltage beyond its 100-V rating, and the 100-W lamp will be subjected to a voltage below its 100-V rating. Therefore, the 40-W lamp will burn much more brightly than the 100-W lamp.Incidentally, the symbols for the 'watt' and 'volt' are upper, not lower, case: W and V.
Why is there less current in a circuit with four bulbs than there is in a circuit with one bulb?
yes because of bulb resistance :)
If a 12 volt parallel circuit has 4 lamps and each lamp consumes 1 amp what is the resistance of each lamp?
Assuming you mean the 4 lamps are in parallel with each other: the total voltage drop across each lamp is still 12V. As we know that V= IR (Voltage = I Current times Resistance) 12 = 1 x R so Resistance = 12 Ohms for each lamp.
Which has a higher resistance 50W lamp bulb or a 25W lamp bulb and how many times?
R1=v square/50 R2 = v square/25 = v square/25 multiplied by 2/2 = 2v square/50 R2 = 2 multiplied by R1 R2 is twice more than R1
A 60-watt 120 volt lamp requires morecurrrent than a 40 watt 120 volt lamp?
Yes. A 60W bulb has a higher resistance than the 40W buld. The extra resistance requires more current to light up the bulb. The fillament then glows brighter.
Can I use a higher wattage bulb in a lamp that states 40 watts?
You should not use a higher wattage bulb in a lamp that says 40 watts. The higher wattage could cause the lamp to catch fire due to the excess heat and could cause you serious electrical problems.
What degrees is it under a lamp?
Depends on the lamp and bulb if you are referring to temperature. Directly related to energy wasted as heat and not converted to lumens. The element or filament has a higher resistance and displaces heat. Inefficient unless heat is your goal as with a heat lamp. If you are referring to degrees of diffusion; that depends on the bulb or the shades diameter, the shades reflectivity and distance of the light source to the end of the shade.
Why does a 25 watt bulb glow brighter than 60 watt in a series circuit?
Because the filament of a 25-W lamp has a higher resistance than that of a 60-W lamp and, therefore, will experience a greater voltage drop -the lamp with the voltage drop closer to its rated voltage (in this case, the 25-W lamp) will be the brighter.
Is resistance in the filament of a lamp essential or not?
Yes, the resistance of the filament of a light bulb is what generates enough heat to make the filament glow and produce light.
Does the glow of bulb depend on current or voltage?
Since the bulb has a constant resistance, increasing the voltage will increase the current which will increase the brightness until the bulb blows in a flash of light.Ohm's Law governs this process where Volts = Current x Resistance.Another Answer Incandescent lamps do not have a constant resistance, as their resistance increases significantly with temperature. In fact, the 'hot resistance' of a lamp filament is around 10-18 times higher than its 'cold resistance'. The temperature increase, of course, is due to the current passing through the filament. This means incandescent lamps do notobey Ohm's Law and are, thus described as being 'non-ohmic' or 'non-linear'. However, to answer your question directly, the rated power of a lamp only occurs at the lamp's ratedvoltage. Even a small reduction in voltage will result in a significant loss of power and, thus, brightness. So, in this sense, a lamp's brightness is determined by the voltage applied across its filament.
Why the slope of voltage-resistance characteristic increases in the case of tungsten lamp and decresing in case of carbon lamp?
If the filament really was made from a material that has a negative temperature coefficient (as temperature increases, resistance decreases) then the decreasing resistance would cause more and more current to be taken as the lamp heated up and the temperature would get higher and higher in a runaway manner until either the power supply's breaker would trip or (more likely) the light bulb's filament would simply burn open. In fact the filament has to be made from a material that has a positive temperature coefficient. (As temperature increases, resistance increases.) Then, as the bulb's temperature rises, its filament's increasing resistance causes less current to be taken than when it was cold. Quite quickly a stable "steady-state" temperature and "running" resistance is reached so that the bulb simply continues to give out a steady amount of light according to the current it is taking from the electricity supply.
What desk lamp gives the most light?
A desk lamp which takes a regular size bulb. You could easily change it to a higher watt.
WhY does a filament lamp get when you us high voltage?
because there is a correlation between resistance and voltage and current. The equation resistance = voltage divided by current shows that the higher the voltage, the bigger the resistance,, and the bigger the resistance the hotter the filament lamp will get because of the electrons bumping into each other which means there is a loss of energy and that energy is being transferred to the filament making the actual filament bulb hot since there is more thermal energy wasted at the end.
What is another word for light bulb?
Incandescent lamp
If you have 2 5-watt bulbs connected in series and then in parallel which circuit arrangement will give you brighter bulbs?
It depends on the voltage rating of each lamp, and the value of the supply voltage. It's important to understand that a lamp will only operate at its rated power (therefore at its full brightness) when subject to its rated voltage.So, let's assume each lamp is rated at, say, 24 V.If connected in parallel across a 24-V supply, then they will both operate of full brightness.If connected in series across the same 24-V supply, then each lamp will be subject to half its rated voltage, and will be very dim.On the other hand, if connected in series across a 48-V supply, then they will each be subject to 24 V, and will both operate at full brightness.
