0
Why is there a difference between dc pass through and bidirectional with coaxial splitters?
Wiki User
∙ 14y ago
A DC pass through will pass a DC voltage in only one direction. Bidirectional will let a DC voltage travel both directions.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What cables carry the signal from a cable modem to a PC is it a RCA cable HDMI ethernet or coaxial?
coaxial
The center copper core of coaxial cable is called what?
Coaxial cable has a center core of copper wire surrounded by a layer of insulation, which is in turn surrounded by a conductive braided shielding and encased in a final insulation sheath. The center copper core and the braided shielding layer act as two independent conductors, thus allowing two - way communications over a coaxial cable.
What are the disadvantages of using coaxial cable?
scattering, costs high than wireless communication, difficult to maintain,splicing should be perfectly taken care ,otherwise the loses increases in the optic fibres
Is Coaxial cable is the fastest transmission media?
no. fiber optic is the fastest physical transmission media right now, due to the fact that it uses light (so the data moves at the speed of light) instead of coaxial's electric signals (which can be affected by outside sources and slow the transmission down).
How do you hook up cable to a TV with a broken coaxial input but has the three AV inputs?
If your television has a broken coaxial input but has three AV inputs (Red, White, and Yellow), and your cable box has the same AV inputs in the back of it, which they usually do, all you have to do is connect the cords from the cable box to the TV(if you dont have the RCA cords, these can be purchased at any electronic store). Instead of putting your TV on channel 3 or 4 as you would when the cable is hooked up by coaxial, switch your channel to one of your Input or Video channels, as you would do if you were trying to watch a VHS tape or DVD. You'll see that the AV outlets provide just as good of a picture as the coaxial hookup.
Difference between coaxial cable and STP cable used for computer networking?
Difference between coaxial cable and STP cable used for computer networking?
How many coaxial splitters can you use?
It depends on your signal level and the signal necessary for your equipment. Each splitter reduces the available signal level to items that are downstream.
Difference between coaxial cable and wave guide?
Waveguides are used at higher frequencies where their loss is lower than coaxial cable. Coaxial cable is used at lower frequencies where waveguides are too large and heavy. Lastly Coaxial cable is also used at higher frequencies where some flexibility is required.
What is the difference between the guided and unguided?
guided media is that media which use some physical path like coaxial cable fiber optics etc
What is the difference between center lathe and capston?
The centre lathe has only one coaxial tool, whereas the capstan has a rotating multi tool station with indexer and clutch.
Is a flat-panel coaxial cable different from a regular coaxial for TV/VCR use?
The only difference would be if the VCR or TV is not digital otherwise it should be fine.
The difference between UTP cable and Coaxial cable?
A UTP cable has 4 pairs of twisted wires. In a coaxial cable, there are two conductors, one inside the other. Since they have a common center, or axis, they are called "coaxial" (co-axial).A UTP cable has 4 pairs of twisted wires. In a coaxial cable, there are two conductors, one inside the other. Since they have a common center, or axis, they are called "coaxial" (co-axial).A UTP cable has 4 pairs of twisted wires. In a coaxial cable, there are two conductors, one inside the other. Since they have a common center, or axis, they are called "coaxial" (co-axial).A UTP cable has 4 pairs of twisted wires. In a coaxial cable, there are two conductors, one inside the other. Since they have a common center, or axis, they are called "coaxial" (co-axial).
Can a coaxial cable for a TV go bad Can you suddenly lose the signal from an antenna because of a bad cable or connection from the TV to the wall jack Will a new cable solve this problem?
Yes! a coaxial cable can go bad. Yes! you can suddenly lose the signal from an atenna because of a bad cable. A a new coaxial cable may fix the problem as long as the damaged cable is the source of the problem. However if the signal problem is at the tap or one of the splitters in your home you will need to call your cable company to fix the problem.
What is the difference between baseband coaxial and broadband coaxial cable?
The difference between baseband coaxial and broadband coaxial cable is baseband coaxial technology uses digital signaling in which the cable carries only one type of digital signal. Where as the broadband coaxial technology typically transmits analog signals and is capable of transmitting multiple frequencies of data simultaneously.
What is use coaxial cable?
Uses of Coaxial Cable?
What is slower coaxial cable or optical cable?
Coaxial one.
What is the purpose of a coaxial cable?
The purpose of a coaxial cable is to act as a transmission line for a radio frequency signal. The electromagnetic field carrying that signal exists only in space between its inner and outer conductors.
