0
You connected PS3 with HDMI cable and when it was switched back to 3 RCA plugs 480i cable PS3 not working you think it is stuck on the HDMI settings what do?
U shut off the power on the back and then flip the switch back on. Next make sure the light on the front is red. Finally u hold on to the power button for about 5 secs until u hear a beep. Let go and wala. (it may take a few secs to work)
There are some tricks to do things on the PS3 and can be found under the site Secrets of the PS3 under Super Secrets. Since it has the answer to this question I though maybe a link to help and have added it under related link Here is what was provided for the solution to the problem and there are others at the site:
Hold Power button down for two beeps (while PS3 is off): Reset video to lowest settings.
What else can I help you with?
Your sony flat screen was working fine with your PS3 but now when you turn your PS3 on it says no signal What is wrong?
It is your TV that is saying no signal and not the PS3. When it happens to me it is when the TV is not switched to the correct source. For me this is when the HDTV is still at the PS3 source of HDMI or HDMI-3 plug and not the cable HDMI plug or HDMI-1. It can also happen when you purchase a cheap HDMI cable that stops working or when something is just disconnected from either end of the PS3 A/V or HDMI cable
Can you plug your PS2 to a television that is not connected to cable?
nope
How do you set up ps3 for wired internet?
To set up a wired internet connection on your PS3 first make sure that you have an ethernet cable from a router with internet plugged into your PS3. Next go into Settings>Network Settings>Set Up Connection. Follow the instructions on screen making sure you input valid information about your network. Submit and your PS3 should now be connected to the internet using the Ethernet cable!
How can you hook up a Mitsubishi projection tv to play 3d on ps3?
If it is a 3D projection HDTV just change your settings after plugging in the HDMI cable. Otherwise the PS3 does not play 3D without being connected to a 3D HDTV
Why is my tv showing a simplink please try again message?
The "Simplink Please Try Again" message on your TV usually indicates an issue with the HDMI-CEC (Consumer Electronics Control) feature, which allows connected devices to communicate. This could be due to a faulty HDMI cable, an incorrectly configured device, or compatibility issues between the TV and connected devices. Try disconnecting and reconnecting the HDMI cable, ensuring that Simplink is enabled in your TV settings, or restarting both the TV and the connected device. If the problem persists, check for firmware updates for your TV or connected devices.
How do you get internet for your PS3?
You have to have a router, or a wireless ethernet cable. Then once it is connected you go to settings and network settings, then go to connection settings and fill out the correct info for your connection.
How do you fit a speedometer cable on vauxhall combo?
speedo connected to gearbox and connected to other end not brken but not working
Why wont my 1995 Nissan maxima trunk open?
The cable or lock connected to the cable is not working. The body or trunk is bent.
How do you connect your PS3 online with an ethernet cable and cable modem?
You purchase a router and connect it to the cable modem and then connect everything to the router. Otherwise you have to unplug whatever is connected to the cable modem (for example a PC) and plug in the PS3 . Whatever you have unplugged is no longer connected to the internet until you unplug the PS3 and plug it back into the modem. Once the PS3 is connected to the cable you need to go to network settings on the PS3 and set up the network connection.
Is it possible to jump start a car with the positive cable connected first and the negative cable connected second"?
No, it is not possible to jump start a car with the positive cable connected first and the negative cable connected second. The correct order is to connect the positive cable first and then the negative cable.
Why is minecraft split screen not working on ps3?
Make sure your console is connected to your TV via a HDMI cable. Without that specific cable, Minecraft will not allow split screen.
Why is my guitar not working when connected to the amp?
Your guitar may not be working when connected to the amp due to issues such as a faulty cable, a problem with the amp or guitar input, or a dead battery in an active pickup system. Check these components to troubleshoot the issue.
95 Honda accord and have replaced the speed control sensor but the speedometer is not working?
Since you replaced the sensor, and the speedometer still isn't working it is possible that you will need to replace the speedometer cable. Check the cable first to be sure that it is still properly connected, and if so replace the cable to see if that solves the problem.
How do you jump start a car, and should the red or black cable be connected first?
To jump start a car, first connect the red positive cable to the positive terminal of the dead battery, then connect the other end of the red cable to the positive terminal of the working battery. Next, connect the black negative cable to the negative terminal of the working battery, and finally connect the other end of the black cable to a metal surface on the car with the dead battery, away from the battery. Start the working car and let it run for a few minutes before attempting to start the dead car. The red cable should be connected first.
How GPRS Moden can be connected to system?
A GPRS modem can be connected to a system via USB, serial port, or Ethernet, depending on the modem's design. For USB modems, simply plug the device into a USB port and install any necessary drivers. Serial modems typically connect using a serial cable to a COM port, while Ethernet modems can be connected to a network router or switch using an Ethernet cable. Once connected, configure the modem settings through the system's network settings or dedicated software to establish a data connection.
Is the negative battery cable considered as the ground?
The battery cable that is grounded, is connected to the body of the vehicle. Sometimes it is the negative cable & sometimes it is the positive. You need to check which cable is connected to the body of the vehicle.
What happens when you plugin the Ethernet cable to your PC?
when ethernet cable is plugged in it is detected by ethernet card. if the cable is connected to network it detects that network and dispalys " you are connected to network"
