0
What else can I help you with?
How do you clear code wait after entering the wrong radio code on BMW roadster?
If it states code wait on the radio then you must turn the key to the first click or position in the ignition then allow the vehicle to sit for 1 hour. After 1 hour you will be able to re-enter your code incorrectly up to 3 times before it will state code wait on the radio again.
How do you clear code wait after entering the wrong radio code on BMW 328I?
Leave the unit on for at least an hour, maybe even an hour and a half. 'Code Wait' should go away and you should then be able to input the correct code; only three tries!
Jeep radio broken says wait 2 hrs?
It's not broken, the power has been disconnected(flat battery, radio removed, blown fuse). Just do as the radio says, turn the key to the auxillary position, switch the radio on, wait 2 hrs and then enter the code.
How do you use the word radios in a sentence?
Please help me to decide which of these two radios is the better bargain. We'll have to wait until the recon team radios in their coordinates.
How do you enter Nissan navara D22 radio code?
To enter radio codes for your Nissan Navara D22, check the owner's manual. There will be specific instructions on how to enter your code correctly.
How do you get rid of wait one hour Nissan Micra radio?
The message of wait one hour occurred because a wrong passcode was entered into the system. To get rid of the message you will need to leave the radio on and uninterrupted for the one hour. The radio will then reset itself and will be fine again.
How do you clear code wait after entering the wrong radio code on BMW roadster?
If it states code wait on the radio then you must turn the key to the first click or position in the ignition then allow the vehicle to sit for 1 hour. After 1 hour you will be able to re-enter your code incorrectly up to 3 times before it will state code wait on the radio again.
How do you clear code wait after entering the wrong radio code on BMW 328I?
Leave the unit on for at least an hour, maybe even an hour and a half. 'Code Wait' should go away and you should then be able to input the correct code; only three tries!
Trying to re-code radio in vauxhall vectra which has been bloked after 3 attempts?
Firstly, get the right code! Then turn the ignition on, turn the radio on, and wait about half-to-one hour. Then you can try again.
How do you enter the code on your radio after disconnecting and connecting the battery back on the 1993 XJ6?
Turn the key to acc to allow the radio to come on, wait for it to display CODE, and then enter your 4 didgit radio code. If you make a mistake, turn the key off and on, and try again. If you make 5 mistakes, turn the key on to acc, wait 1 hour, and it will reset.
Dodge sprinter van radio says wait?
So wait
How do you get the wait signal off the radio on ML 350?
Turn the ignition lock on and the radio on and wait. It can take up to a couple of hours depending on how many times the incorrect code has been inputed in the radio.
Land Rover radio code says Wait. What do I do?
Every time a wrong code is entered the wait time doubles, you must just sit the wait time out with ignition on & re-enter correct code ( various proceedures for various models) or try disconnecting battery for an hour or so....... Good luck :-)
How do you enter radio codes for 1990 190e?
Turn your ignition swith to on position,turn your radio on,code should appear on the screen of your radio. After code appears,enter first digit of your code. wait for first digit to flash. Then enter second digit,wait for flash,Then enter third digit,wait for flash. Then enter fourth digit, wait for flash. Then push * on your radio to except the code.
Mercedes radio slk stays on wait?
If you've recently interrupted the power supply (battery) then you will need to input the radio code. The code should be in your paperwork, if not, contact your dealer for the code. The "WAIT" code on the radio means you have input the wrong code more than 3 times and you have to wait 10 minutes before attempting to enter radio code.
What part of a radio is the process?
Please wait while loading...
Jeep radio broken says wait 2 hrs?
It's not broken, the power has been disconnected(flat battery, radio removed, blown fuse). Just do as the radio says, turn the key to the auxillary position, switch the radio on, wait 2 hrs and then enter the code.
