answersLogoWhite

0

Go to a good dealer, they'll sell you the appropriate adapter to plug the radio right in w/o any messing about with cable splices.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Music & Radio

How can you find out what wires go to what when replacing a Dodge Stratus factory radio with a new one?

One of the easiest and quickest ways to do this, is to go to an audio store and buy a wire harness. It should plug right into the factory plug (providing that it is still intact) and then plug into your new radio. If not, it will have ready to go wires for the harness that came with your radio.


What do you do if your aftermarket radio wiring harness does not match the factory wires?

Many aftermarket companies sell adapters for aftermarket wire harnesses. They have the original factory harness at one end and you cennect that to the harness that came with the radio. Check your local car audio installer.


Fitting a radio in Peugeot Expert?

To fit a radio in a Peugeot Expert, start by carefully removing the dashboard panel using a trim removal tool to avoid damage. Disconnect the existing radio by unplugging the wiring harness and antenna. Install the new radio by connecting it to the wiring harness and securing it in place, then reattach the dashboard panel. Finally, test the radio to ensure it powers on and functions correctly before fully reassembling.


Can a speaker wire harness be used to connect the cars harness to a new after market radio?

it might, it depends on the brand of the new radio and what plugs they use. if not, most good electronic stores sell adapters to join different brands if you dont want to strip and splice the wires by hand.


What is the wire harness for 2004 Hyundai Santa Fe with monsoon radio?

gm/Pontiac radio harness

Related Questions

When installing a new radio in a 1994 Toyota Tercel how do you distinguish which wires are what concerning the radio?

Usually the aftermarket radio you put in needs a wiring harness you can buy at most audio stores and big electronic stores like Best Buy. The back of the package will tell you which wires connect by color. Remember, solder is the best tool for connecting wires but usually permanent.


What do the stripes indicate on the green and blue wires on a 1992 Ford Festiva radio harness?

speaker wires


Radio wiring diagram 2007 Chevy silverado?

Here is the info in your vehicle: Radio 12v red/white + radio harness Radio Ground black - radio harness Radio Ignition (GMLAN Serial Data) Radio Illumination yellow (dimmer) + radio harness Factory Amp Turn-on same as power antenna wire Power Antenna white + radio harness LF Speaker +/- tan - gray +,- radio harness or amplifier Notes: If equipped, the amplifier is under the rear of the center console. At the amplifier, the left subwoofer wires are dk. blue/white (+) - lt. green/black (-). The right subwoofer wires are dk. green (+) - lt. blue/black (-). RF Speaker +/- lt. green - dk. green +,- radio harness or amplifier LR Speaker +/- brown - yellow +,- radio harness or amplifier RR Speaker +/- dk. blue - lt. blue +,- radio harness or amplifier


What color are the 12 volt wires on a Geo metros radio wire harness?

red and yellow


What kind of wiring harness is used for a 03 Pontiac sunfire in the radio?

For a 2003 Pontiac Sunfire, the radio typically uses a standard aftermarket wiring harness, specifically a harness compatible with GM vehicles. This harness usually contains a combination of color-coded wires that connect the vehicle's audio system to the aftermarket radio, allowing for easy installation without cutting factory wires. It's advisable to check for compatibility with your specific radio model to ensure proper connections.


What is the wiring diagram for 2008 Honda Civic si radio?

DIRECTWIRE™ WIRING INFORMATION - HONDA / CIVIC / 2006 / Audio [PRINT THIS PAGE] Radio 12v white + radio harness Radio Ground black - radio harness Radio Ignition purple + radio harness Radio Illumination gray or red/black + radio harness Factory Amp Turn-on lt. blue + radio harness Power Antenna gray + radio harness LF Speaker +/- lt. green - pink +,- radio harness or amp under ctr dash Notes: On vehicles with the amplifier, the LF tweeter wires are red (+) - green (-). RF Speaker +/- gray - brown +,- radio harness or amp under ctr dash Notes: On vehicles with the amplifier, the RF tweeter wires are pink (+) - blue (-). LR Speaker +/- yellow - brown +,- radio harness or amp under ctr dash RR Speaker +/- blue - orange +,- radio harness or amp under ctr dash Notes: On vehicles with the amplifier, the subwoofer wires are green (+) - red (-). Interface Module: Category: Immobilizer Bypass Required: Yes Type: Transponder Part #: 556UW Alternate Part1 #: 555U Alternate Part2 #: DesignTech 20402 Alternate Part3 #: DesignTech 29402 Notes: Standard on all models.


How can you find out what wires go to what when replacing a Dodge Stratus factory radio with a new one?

One of the easiest and quickest ways to do this, is to go to an audio store and buy a wire harness. It should plug right into the factory plug (providing that it is still intact) and then plug into your new radio. If not, it will have ready to go wires for the harness that came with your radio.


What do you do if your aftermarket radio wiring harness does not match the factory wires?

Many aftermarket companies sell adapters for aftermarket wire harnesses. They have the original factory harness at one end and you cennect that to the harness that came with the radio. Check your local car audio installer.


How the wires from the door 4 speakers connect to the radio?

The wires from the door speakers connect to the radio via the vehicle's wiring harness. Each speaker typically has two wires: one for positive and one for negative, which correspond to the output channels on the radio. The radio sends audio signals through these wires, allowing the speakers to produce sound. Properly matching the colors and connectors of the wires ensures that the speakers function correctly with the radio.


How do you replace a 2000 impala amfm with a 2002 amfm casscd player and by pass security lock?

If you are simply installing a different "aftermarket" radio then all you really have to do is pull the old radio out. Purchase a "wiring harness" specifically for you vehicle. Plug that into the wiring for the radio (from your vehicle) and plug the other end into the back of the radio. You can do it by splicing and connecting all the wires but that is not worth it all things considered.


What do you do if there were four wires left over after replacing the stock radio in a 91 Toyota Camry with a new CD player and the dash lights do not work?

When you purchased thr aftermarket radio, the sales person should have prompted you to also purchase a wiring harness to fit the radio into your vehicle.You should have at that only 2 wires left over. the first is blue with a white stripe, which would control the power antenna, or amplifier lead, and can be capped if you have neither. the second is an orange lead which would control the radio dimmer lights.if your vehicle, and radio are equipped with the dimmer then connecting with the wiring harness should take care of your problem


A radio wire harness diagram for a 2000 Ford Explorer?

I would like to find a diagram for the car radio speaker wires on a 2000 ford explorer