There is a code inside the cover of the folder of books that came with the car and an instruction manual of how to put the code into the car
you must re enter the security code for the radio to work
yes. once you put the code in press the sc button
look to the right of the radio for a button that says clock. push it and your display shoulg show "set hour" or something similar. use the radio tuning knob to set the hour. push the button again for minutes and use the tuning to set them. if you have an older van there 2 small/tiny buttons to the right of the radio display screen. use a pen tip to push them. they are marked HH and MM.
Assuming you have the 4 digit unlock code for your radio: 1. Hold AS button down and turn radio on - keep button held down. 2. You will be prompted to enter the code so let go of AS button: 3. Use the '1' button to select the first digit, the '2' button for the second etc... 4. When you have used buttons 1 - 4 to enter the correct code, press the AS button again for the last time - bingo! unlocked!
Turn your car on, so that the radio can be turned on and off. Then turn your radio off. After is it off, push the clock button and while holding clock, use seek to change the hour and tune to change the minutes.
you must re enter the security code for the radio to work
remove radio out vauxhall vectra
Turn the radio on. Press SET button. This puts the radio in (Program) mode. Press SEL button. This puts the radio in (Set Hours) mode. Press TUNE button up or down to adjust hours. Press SEL button. This puts the radio in (Set Minutes) mode. Press TUNE button up or down to adjust minutes. Press SEL button again to return to normal mode. Pressing the SEL button after this changes the display to (Radio Frequency) display or (Time) display.
You probably have led's failing,a complete display replacement is the only real solution.
I don't believe you can display both the radio station and the clock at the same time. With the radio on push the "CLK" button, that will display the time and I believe when you change radio stations it will display the station # temporarily before returning to the clock display.
I tried to decode my radio the trouble is i had 4 attemps and an error is showing how do i solve the problem
Read the owners manual. Turn the key to the on position (not start) with the radio off. Wait 10 seconds. Press the "display" button on the radio and hold for 10 to 12 seconds. the radio display will light up . PRESS "display" and "1" to select functions. display i think is enter . read owners MANUAL. It's really simple. Turn the key on but not to start the engine. Make sure the radio is off and hit the "display" button for a couple of seconds, the big knob on the bottom on the left of your radio until the "settings" display shows. Hit the scan button to the right until "Tire pressure" comes up. Hit # 1 on your radio select buttons until it says "reset". Push the "display" button until you hear a "beep". Press the scan button a couple of times until it says "exit" then press "display". After it "beeps" you're all done. If you had an owners manual why would you ask for help.
yes. once you put the code in press the sc button
Push the volume control button in and release. Do this 4 time (i believe) you will be scrolling from bass to treble, fade and then display. When you are on display move the the volume button down to lighten and up to darken.
Insert the ignition key, and turn it to the ACC (accessory) position. Turn off the radio. Press the display button until Oil Life shows on the radio display. Press the seek button until Tire Pressure Monitor displays. Press the 2nd preset/#2 button. Press the display button again. The tire pressure monitor should now be reset.
look to the right of the radio for a button that says clock. push it and your display shoulg show "set hour" or something similar. use the radio tuning knob to set the hour. push the button again for minutes and use the tuning to set them. if you have an older van there 2 small/tiny buttons to the right of the radio display screen. use a pen tip to push them. they are marked HH and MM.
If you have the factory radio this wont be a problem. Turn the radio off. The push in the DISP button, which is the bottom dial below the power button. When the radio display settings, use the seek button until oil life is displayed. Then press the 1 or 2 button util the display says reset. The hold the DISP button again and the light will go off. This process is also outlined in the owners manual under radio. If you don't have the factory radio push the gas pedal down 3 times with the key in the "on" position without the car being on, and this should do it.