you need the 4 digit code that came with the vehicle s radio maybe original dealer has a record of it
I just purchased a 2009 Jetta SE and the radio was in SAFE 2 mode. The dealer tried the radio code but could not get the radio to a point to enter it. I read a number of threads and tried many suggestions, leave the car in the Aux mode for an hour, hold down the seek and mode buttons etc. Finally I disconnected the battery waited a few moments and re-connected. I figured maybe this would show me the screen to enter the code but instead the radio booted up with no code and works fine. The dealer suggested I return when the service dept was open, none of the sales people had a clue.
To take a Bentley Arnage radio off safe mode, you typically need to enter a security code. This code is usually provided in the owner's manual or can be obtained from a Bentley dealership. After powering on the radio, follow the prompts to enter the code. If you don't have the code, it's best to consult your dealership for assistance.
I own a 2000 Audi A6 The battery was changed & I can not find the radio code to release the safe mode My vin # is WAUEH24B2YN010658 Any help would be greatly appreciated thankyou Bruce Klein
To reset the Audi radio code when it displays "SAFE 2," you'll need to enter the correct security code. First, turn on the ignition but keep the radio off. Then, hold down the "TP" and "RDS" buttons simultaneously until "SAFE" appears. After that, use the radio preset buttons to enter the code, followed by pressing the "TP" button to confirm. If you don't have the code, you may need to consult your owner's manual or contact a dealer for assistance.
I think its kinda simple: If your car takes that long to start...(More than three to four seconds) Get to a Mechanic second to more directly answer the question.. Either the lead to the radio Memory is hooked to the ignition incorrectly. Losses power when turned to the "power Starter" position. OR The battery is so weak that when under load it doesn't have enough "juice" to power the memory wire from its "normal" position. Looking close at the context of your question and taking out the "I Dont know anything factor..." I am guessing it is clear you have an after market radio hooked up and it is not hooked up correctly. See Memory wire in your direction (usually Yellow) or check for a blown fuse or bad wire with an Audi Radio. (installed by the factory) More on "SAFE MODE": ***When you loose power to the memory the radio will stop remembering the CODE...*** This is a safety feature in Audi(s) to reduce the number of radios stolen around the world. Great feature, YES and NO... not many Audi radios are stolen because of it. HEY , When you know something ... PASS it on! D SUPER MECH-NIC
I have an 1996 Audi Quattro A6 i changed my batteri and my radio went to safe mode. How do i get my radio off safe mode?
You need your operator's folder. In there is a booklet about the radio. it will have a code you need to enter to get the radio out of "safe" mode. the code is unique to each radio and car.
You need the serial number from the side of the radio and also the VIN number. You call an Audi dealership and give them the two numbers and for a $30.00 fee they will give you the radio code to take the radio off of "safe" mode. Lewis Powell
Need to get the code from the dealer. Have the VIN, and proof of ownership (registration), and your license ready.
Your safe code for your radio is unique to the vehicle. You can go have it reset at an Audi dealership for $20-40 dollars.
My car is a 2000 VW Polo, I just power on and off the radio about fifteen - tewnty times and it comes out of safe mode.
The Radio "Anti-theft" code use to given from dealer ( first owner bought the car) If you don't have or lots the code you only can get the code from dealer. In manual book "Audio Symphony" book have the radio code it calls "Radio card"
Take the radio out of the dashboard, the code is on the side of the radio.
the radios have a safety device on them...maybe the battery died once or the radio was disconnected on some point. so it may be in safe mode, call the dealer and give your VIN they should tell you how to activated.
Turn the ignition to the on position but do not start the engine. Leave it sitting like that for one hour. The radio should then switch out of safe mode and allow you to enter the correct code.
Well, when your radio is in safe mode, it usually means that the security code needs to be entered to unlock it. You can find this code in your car's manual or sometimes on a card that came with the vehicle. Just enter the code using the radio preset buttons, and your radio should come out of safe mode, allowing you to enjoy your favorite tunes once again. Just take your time, follow the instructions, and soon enough, your radio will be back to normal.
i have brought a car but the radio is showing safe mode and unfortunately i do not have a code are you able to supply the code radio is blaupunk 300 car is a vauxhall zafira 2002