To reset the Audi radio code when it displays "SAFE 2," you'll need to enter the correct security code. First, turn on the ignition but keep the radio off. Then, hold down the "TP" and "RDS" buttons simultaneously until "SAFE" appears. After that, use the radio preset buttons to enter the code, followed by pressing the "TP" button to confirm. If you don't have the code, you may need to consult your owner's manual or contact a dealer for assistance.
If you want to reset your code for your safe, you must first remember the original code. If you cannot remember the original code, you will need to contact customer service for assistance.
To reset the code on a Sentry safe, you typically need the original factory code or access to the safe. If you have the factory code, open the safe, locate the reset button (usually on the inside of the door), and follow the manufacturer's instructions to set a new code. If you've lost both the code and key, you may need to contact Sentry's customer service for assistance or consider a locksmith. Always refer to the specific manual for your model for detailed instructions.
remove the radio of the car than it will be a # on the radio call your locar vw service dealer to ask for the code.
you need the 4 digit code that came with the vehicle s radio maybe original dealer has a record of it
How do you reset Radio Code for 2000 E320? I just purchased the car and had to get new battery installed and know the radio doesn't operate until you reset with the code. Previous owner lost this card with code! Any direction would be great!ThanksRadio codeI called Mercedes Benz of Portland , Oregon and gave them my VIN # and in return they gave me the code! That easy. Entering the code:On my 1997 E320, I typed in the 5 digit code and then pressed the "SC" button (over by the Seek and Tune buttons) to activate the code. The Dealer told me to use the "OK" button, but my radio did not have one, I guess about the "SC" button and that was correct on my radio.
Your safe code for your radio is unique to the vehicle. You can go have it reset at an Audi dealership for $20-40 dollars.
To reset the radio code in a 1997 Audi A8, you typically need to turn on the ignition, then turn on the radio. If the radio displays "SAFE," you will need to enter the correct code. This code can usually be found in the owner's manual or provided by an Audi dealership. If you don't have the code, you may need to contact a dealership with your vehicle identification number (VIN) for assistance.
If you want to reset your code for your safe, you must first remember the original code. If you cannot remember the original code, you will need to contact customer service for assistance.
To reset the code on a Sentry safe, you typically need the original factory code or access to the safe. If you have the factory code, open the safe, locate the reset button (usually on the inside of the door), and follow the manufacturer's instructions to set a new code. If you've lost both the code and key, you may need to contact Sentry's customer service for assistance or consider a locksmith. Always refer to the specific manual for your model for detailed instructions.
You need your operator's folder. In there is a booklet about the radio. it will have a code you need to enter to get the radio out of "safe" mode. the code is unique to each radio and car.
i got it i had to hold down AS and RDS to input the code.
I have a brinks 4 no. Safe gorgot the turning sequence for it can u help?
Usually most safes/gun safes have a reset button on the inside of the safe.
To change the passcode on a stack-on safe, first, open the safe using the current code. Locate the reset button or switch, usually found inside the door or on the back panel. Press and hold the reset button while entering your new passcode, then release the button to save the new code. Finally, test the new passcode to ensure it works correctly before closing the safe.
When you purchase the safe you should get the combination sequence with it. If the sequence needs to be reset or the tumblers malfunction you will need to call a locksmith to have the internal pins reset. If you lose the code or combination, a locksmith will be able to reset it without damaging the inner mechanisms.
change the sencer related to the code and reset the computer problem solved drive safe
You need the serial number from the side of the radio and also the VIN number. You call an Audi dealership and give them the two numbers and for a $30.00 fee they will give you the radio code to take the radio off of "safe" mode. Lewis Powell