0
If it's anything like the 2005 model, you should have two long "keys" which slot in the sides of the stereo and push the clips, so the device can slide out.
If you don't have these, you can buy them (although they do vary slightly between manufacturers, most are very similar) or you can try to use a couple of teaspoons.
What else can I help you with?
Remove 1993 Toyota Camry factory radio?
Remove the 1993 Toyota decorative radio cover in. Remove the radio retaining screws. Pull the radio out. Remove the wiring harness.
How do you remove a stock radio from a Chevy Metro?
im trying to find out the same thing
Remove a stock radio from vs commodore?
you will need to unscrew your dash and pull off the front plate of your dash, then you will need to unscrew the stock radio, then you will need to go ahead and pull out the adapter from the back of your radio.-Shocker
How do you remove a Ford pick-up stock radio?
I did this not long ago in my ranger. There are four hole in the front of the radio, you must remove the trim around it to see them. They are on the four corners. They make a tool that fits in the holes and pushes the clips in and the radio pulss free. I used four drill bits that just fit in the holes. luck.
How do you hook up Satellite radio to stock Radio in 2005 Chrysler 300c?
To hook up satellite radio to a stock radio in a 2005 Chrysler 300C, you will typically need a satellite radio tuner compatible with your vehicle. You'll also need an FM modulator or an auxiliary input adapter if your stock radio lacks direct inputs. Install the tuner according to the manufacturer's instructions, connect it to the vehicle's power source, and then tune your stock radio to the designated frequency or input for the satellite signal. Finally, secure the antenna on the vehicle's roof for optimal reception.
Remove 1993 Toyota Camry factory radio?
Remove the 1993 Toyota decorative radio cover in. Remove the radio retaining screws. Pull the radio out. Remove the wiring harness.
How do you remove the stock on a Winchester model 290 .22 caliber rifle?
remove the buttplate screws, and the buttplate. In the large round hole in the stock is the stock bolt. That is unscrewed to remove the stock from the rifle.
How remove stock on Winchester model 290?
Leave this to a gunsmith
How do you get the bolt apart on a Cooey Model 600 22 caliber rifle?
. to remove the bolt on this model you must lower the tube assembly,there is a screw under the stock, remove stock first.
Remove stock stereo from Honda accord lxi 1984?
* Remove the ashtray and ashtray holder * Remove the radio and mounting plate screws and lower the radio and unplug the electrical connector and antenna lead then push the radio out of the dashboard
How do you remove a stock radio from a Chevy Metro?
im trying to find out the same thing
Remove a stock radio from vs commodore?
you will need to unscrew your dash and pull off the front plate of your dash, then you will need to unscrew the stock radio, then you will need to go ahead and pull out the adapter from the back of your radio.-Shocker
How do you remove the stock of a model 84 cooey?
Best left to a gunsmith
How do you remove stock radio from a 91 escort?
you will need to unscrew your dash and pull off the front plate of your dash, then you will need to unscrew the stock radio, then you will need to go ahead and pull out the adapter from the back of your radio. and that should do it-Shocker
How do you remove stock radio on Acura CL?
To remove the stock radio from an Acura CL, first, disconnect the negative battery terminal to ensure safety. Then, carefully pry off the trim panel surrounding the radio using a trim removal tool to avoid damaging it. Once the trim is removed, unscrew the mounting screws holding the radio in place, then gently pull the radio out and disconnect the wiring harness and antenna cable from the back. Finally, remove the radio completely from the dashboard.
How do you remove the stock radio in a 1996 Jeep Cherokee?
remove the exterior trim peace that surrounds the outer edges of the radio. Then there should be either two 10mm bolts or four phillip head screws holding the radio in place remove them and gently remove the radio from it slot and then unplug the wire harnesses and antenna in the back of the radio. repeat in reverse to reinstall.
How do you remove the butt stock on a browning model 28?
Best left to a gunsmith
