0
What else can I help you with?
Does lacquer affect cello tone?
Yes, if there is too much lacquer used on a cello then it would produce a more dull sound. Less lacquer means a brighter sound. Some people argue that the type of lacquer can change the sound, but only in a very, very minute way.
How do you remove the lacquer from a saxophone?
If someone has applied a lacquer to stop the brass from tarnishing,it's likely that they have used either acrylic or oil based clear from an aerosol can.(some of the acrylics are of good quality) You should be able to remove it with acetone and clean cotton rags.If a 2-part polyurathane is on it, it will need paint stripper, but this is unlikely.
Refinishing your rg550dy and you need to know how long before it is safe to polish lacquer. I am using nitrocellulose lacquer.?
well it depends on the lacquer and thinner types.... synthetic thinner and lacquers also when applied by spray usually takes several hours but dont take the risk without checking the specifics of you products.... why hurry?
Why do people put lacquer on trumpets?
It prevents the brass from tarnishing, and keeps it shiny.
How do you keep the lacquer from peeling on an alto saxophone?
Unfortunately, as far as I know, there isn't really a way to stop this. The best way to help prevent this is to be very careful with your sax, but it's virtually impossible to keep those pestering little scratches off your lacquer.
How do you remove nitrocellulose lacquer?
Lacquer thinner will possibly remove it, chemical stripper will definitely remove it.
How can I effectively remove rust on a wok?
To effectively remove rust on a wok, scrub the rusted areas with a mixture of vinegar and baking soda, then rinse and dry the wok thoroughly. Apply a thin layer of oil to prevent future rusting.
How do you remove black tar adhesive?
Lacquer thinner will remove it from most materials.
How do you remove printing on PVC pipes?
Lacquer thinner.
How do you remove lacquer from a stone floor?
To remove lacquer from a stone floor, you can use a lacquer thinner or solvent following the manufacturer's instructions. Apply the solution to the affected area, let it sit for a few minutes, and then scrub the floor with a brush or scrubbing pad. Once the lacquer has softened, wipe it away with a clean cloth and rinse the area with water.
Will lacquer thinner remove dried paint from a paint sprayer?
It depends on the type of paint. Lacquer thinner will remove most oil based and latex paints from a paint sprayer, however, spray gun cleaner will remove it better.
We want to remove epoxy phenolic lacquer from tinplate sheet's The Tinplate sheet were first coated with lacquer and than heated at 190 degree Celsius.?
To remove epoxy phenolic lacquer from tinplate sheets, you can try using a mixture of solvents like methylene chloride or acetone. These solvents help break down the lacquer for easier removal. It's recommended to wear protective gloves and work in a well-ventilated area when using these chemicals.
How do you remove oil based paint from door hardware?
Use lacquer thinner on a rough rag. If necessary remove hardware from the door.
How to season a carbon steel wok effectively?
To season a carbon steel wok effectively, first wash and dry the wok thoroughly. Heat the wok on high heat, then add a high smoke point oil like vegetable or flaxseed oil. Use a paper towel to spread the oil around the wok, making sure to coat the entire surface. Continue heating the wok until it starts to smoke, then remove it from the heat and let it cool. Repeat this process several times until the wok develops a dark, non-stick patina.
Oriental Lacquer ?
form_title= Oriental Lacquer form_header= Keep your home beautiful with oriental lacquer. How much lacquer do you need?*= _ [50] Where will you be using the lacquer?*= _ [50] What is your budget for lacquer?*= _ [50]
Where was wok borrowed from?
The wok was invented in 3000 b.c
How do you remove a lacquer floor finish?
We were attempting to remove lacquer from a quarry tile floor. We had inadvertantly put lacquer on quarry tile, which I guess is a no-no. We had a white discoloration that was appearing after only a few days after application. This discoloration was determined to be lacquer that was not bonding properly, and the problem was growing. The only way to correct this problem was to completely remove the lacquer. We sought help through this help sight, but got no answers, so we experimented on our own. We reasoned that lacquer thinner should thin lacquer, so maybe it would remove it. We tried a test area, and it did remove it, but not completely. We deduced that we were only thinning it, and when it dried, there was still just a thinner layer on the quarry tile. So we went to a more powerful thinner- acetone. Acetone has a quicker evaporation rate than lacquer thinner. We used absorbent rags and wiped on the acetone and off with the lacquer ! We had to repeat the process several times with clean rags each time, to get it totally clean. Our rags turned yellow after they dried, indicating to us that we were getting the lacquer finish removed. Keep in mind that we used lots of precautions- cannister-style breathing apparatus, rubber gloves, non-absorbent knee pads, lots of ventilation, etc., etc. We made sure all heaters, etc. were turned off so not to ignite any fumes. DO NOT attempt to take off any lacquer without at least the above protection, if not more !
