0
I'm not positive, but you might take a look at the threads protruding from the nut to see if it is reverse threaded. I know a lot of pinion gears have a reverse thread on them. This would mean you would turn your wrench clockwise to loosen the nut. If you can't see the thread, check with your parts supplier to see if it is a reverse thread.
What else can I help you with?
How do you replace pinion seal 1995 jeep Cherokee?
remove drive shaft. remove large nut on pinion . using a puller, remove yoke from pinion.remove pinion seal. install new pinion seal.replace yoke. install NEW pinion nut,to correct torque specs. reinstall drive shaft.PS now is a good time to replace U-joints while u have drive shaft out
Will 33 inch tires fit on a 1999 Jeep Cherokee Sport?
not without a lift. 30's or 31's will fit as long as you don't articulate too much. You can trim to fit them better and 33's will require a 3 or 4 inch lift with minor trimming. If you go that route you will also need a transfer case drop or slip yoke eliminator to fix your drive line angle.
What are the words of the song 'Take My Yoke'?
The link below is for one song that uses the words ' Take My Yoke'. I know of some others and they simply use the words directly from Matthew 11: 28-30. Come unto me, all ye that labour and are heavy laden, and I will give you rest. Take my yoke upon you, and learn of me; for I am meek and lowly in heart: and ye shall find rest unto your souls. For my yoke is easy, and my burden is light.
What is the name of the song that goes your yoke is easy and your burdens right?
Handel. Messiah
Which one is an unfamiliar term when compared to the rest A yoke B pair C join D marry E elision?
elision
How do you replace pinion seal 1995 jeep Cherokee?
remove drive shaft. remove large nut on pinion . using a puller, remove yoke from pinion.remove pinion seal. install new pinion seal.replace yoke. install NEW pinion nut,to correct torque specs. reinstall drive shaft.PS now is a good time to replace U-joints while u have drive shaft out
How do you remove universal joints 1995 Chevy 2500?
Mark driveshaft, transmission splines, and differential yoke. So that installation will maintain factory balance remove and discard small "u" bolts from differential yoke pry driveshaft out of differential yoke pull drivshaft out of transmission spline shaft bring driveshaft to machine shop to have old universal joints pressed out of shaft and new ones installed or use vise and sockets to drive "U" joints out of driveshaft re-install driveshaft in same position as removed using new "U" bolts
Where is the drive shaft seal 1996 Chevy Tahoe?
The only seals on the driveshaft itself would be on the slip yoke. You're probably thinking of the pinion seal, which is at the front of the differential, behind the input yoke to the differential.
How do you remove the rear drive shaft from a 2000 grand Cherokee Laredo?
Use a crayon or piece of chalk and draw a line on the rear yoke in the differential and on the driveshaft. Do this on the front end of the driveshaft/trany/transfercase also. This is so the driveshaft goes back into the same position you took it from (otherwise you may get a vibration). Undo the 4 bolts on the rear axel yoke. Pry out universal from the yoke. Pull the driveshaft out of the back of the trany/transfer case. You may loose fluid from the trany/transfer case rear seal so check it when you reinstall it
How do you remove a driveshaft from a 1999 gmc suburban?
To remove the driveshaft from a 1999 GMC Suburban, first ensure the vehicle is securely lifted and supported. Begin by loosening the bolts at both the front and rear universal joints using a socket wrench, and then slide the driveshaft out of the transfer case or rear differential. You may need to tap the yoke gently with a hammer to free it if it's stuck. Finally, remove the driveshaft completely and inspect the universal joints for wear before reinstallation.
How do you remove ring and pinion?
To remove a ring and pinion gear, first, safely elevate and secure the vehicle. Drain the differential fluid and remove the differential cover to access the gears. Next, detach the pinion gear by removing the yoke and the pinion nut, then pull the pinion out of the housing. Finally, remove the ring gear by unscrewing the bolts holding it to the carrier assembly, allowing you to extract both components.
How do you change the you joint of a 1997 grand Cherokee Laredo?
To change the U-joint on a 1997 Grand Cherokee Laredo, first lift and secure the vehicle, then remove the driveshaft by unbolting it from the differential and the transmission. Next, use a U-joint press or a hammer to remove the old U-joint from the driveshaft yoke. Install the new U-joint by pressing it into place, ensuring that it’s properly aligned, and then reassemble the driveshaft by bolting it back into position. Finally, check for proper rotation and alignment before lowering the vehicle.
What is torque spec for 2003 Ford Escape rear differential yoke?
23nm/17 ft-lbs
How do you grease slip yoke on 1998 jeep Cherokee xj?
To grease the slip yoke on a 1998 Jeep Cherokee XJ, first, lift the vehicle and secure it on jack stands for safety. Locate the slip yoke on the driveshaft, which connects to the transfer case. Use a grease gun fitted with the appropriate grease fitting to apply grease until you see it oozing out of the joint, ensuring it is well-lubricated. Finally, remove any excess grease and reassemble any components you may have removed for access.
How do you take out the rear axle gear out of the casing do you need a special tool for it does any one have a diagram?
You'll more than likely need to pop the axles out, remove the drive shaft. Remove the nut on the rear yoke and remove the rear yoke (puller). Than you can remove the rear differential by unbolting it behind the cover. this is very dellicate if you dont know what your doing dont do it, this is one of those things to take to a shop cause you can more damage trying to fix it
How do you remove the center support bearing from a 2001 Chevy silverado 2500HD?
The entire driveshaft and stub shaft must be disconnected from between the differential and the transmission. After removal, make match marks on all parts to ensure correct re assembly. Dis-assemble the driveshaft until you are able to remove the yoke that the center support bearing is attached to. Press the yoke out of the bearing and then back into the new bearing.
How do you drop a driveshaft out of a 1993 ford thunderbird LX?
Mark driveshaft, splinced shaft at front of shaft, and rear yoke to ensure that it is replaced at the same position to maintain factory balance Remove and discard small "u" bolts at the differential yoke Pry driveshaft out of yoke and up onto to splines at rear of transmission Drop driveshaft Pull driveshaft off of splined end of transmission Use new "u" bolts on installation
