0
http://customtacos.com/tech/index.php?page=index_v2&id=77&c=6
- follow steps 1-4 - once you get the black trim plate off, the stock radio is held in place by 4 nut/screws. - remove the nut/screws - pull the stock radio out - disconnect the harness - disconnect the antenna - disconnect any auxiliary input devices (i.e. CD changer) if you have them
- when you go to put your new deck in, just follow these steps in reverse
cheers!
What else can I help you with?
Remove 1993 Toyota Camry factory radio?
Remove the 1993 Toyota decorative radio cover in. Remove the radio retaining screws. Pull the radio out. Remove the wiring harness.
What kind of fuse do you need for a blown out radio fuse in a Toyota Tacoma?
the same as what came out
How do I install Radio in Toyota Tacoma?
yes, if going with a single din radio, you will have to buy a kit to fill in the gap.
How do you remove face cover off 2001 Honda crv factory radio?
If you are referring to the factory supplied radio, it is not a 'component' type radio. It must be removed from the dash and dis-assembled.
How do you remove the factory radio to unplug the antenna and install satellite radio wire?
you can't do it yourself you have to get help from a pro
Remove 1993 Toyota Camry factory radio?
Remove the 1993 Toyota decorative radio cover in. Remove the radio retaining screws. Pull the radio out. Remove the wiring harness.
How do you replace a radio in a 2002 Toyota Tacoma?
To replace the radio in a 2002 Toyota Tacoma, first, disconnect the negative battery terminal to ensure safety. Remove the trim panel around the radio using a flathead screwdriver or trim removal tool, then unscrew the factory radio from its mount. Carefully disconnect the wiring harness and antenna cable from the back of the old radio, then connect the new radio's harness and antenna. Finally, secure the new radio in place, reattach the trim panel, and reconnect the battery.
Where is the radio fuse for Toyota Tacoma?
The Toyota Tacoma radio fuse can be located in the fuse box. The fuse box is in the engine compartment. The location of the radio fuse will be listed on the inside cover of the fuse box.
Where is the radio fuse for a 2003 Toyota Tacoma?
The radio fuse for a 2003 Toyota Tacoma is located in the fuse box under the dashboard on the driver's side. To access it, remove the cover of the fuse box, and look for the fuse labeled "AUDIO" or "RADIO." If the fuse is blown, replace it with a new one of the same amperage. Always ensure the vehicle is turned off before checking or replacing fuses.
What kind of fuse do you need for a blown out radio fuse in a Toyota Tacoma?
the same as what came out
How do I install Radio in Toyota Tacoma?
yes, if going with a single din radio, you will have to buy a kit to fill in the gap.
Does a 2013 Tacoma factory radio fit into a 2012 Tacoma?
Yes, a 2013 Tacoma factory radio can fit into a 2012 Tacoma, as both models share similar dimensions and mounting points for the radio. However, there may be slight differences in wiring harnesses and features, so it's advisable to check compatibility and possibly use an adapter for seamless installation. Always consult the vehicle's manual or a professional for specific guidance.
Where is the flasher on a 2006 Toyota Tacoma?
in the center of the car, right under the radio, next to the clock.
How to remove factory radio from 2004 ford f150?
How to remove the factory radio and disconnect wirring harnes in a 2004 f150 ford truck
Where is the lighter and radio fuse located on a 2003 Toyota Tacoma?
In a 2003 Toyota Tacoma, the lighter and radio fuse is located in the fuse box under the dashboard on the driver's side. To access it, remove the cover and look for the specific fuse labeled for the lighter and radio; it is often a 15-amp fuse. You can refer to the fuse box diagram on the cover for precise identification. Always ensure the engine is off before inspecting or replacing any fuses.
How do you remove radio in 1995 Toyota Corolla?
To remove the radio in a 1995 Toyota Corolla, first pry the radio frame from the dashboard using a flat tool like a screwdriver. Then, press in on the pins at each side of the radio and slide it out of the dashboard. Remove the wires from the back of the radio.
How do you take the factory radio out of a 1990 Chevy Caprice?
Begin by removing the decorative cover from your 1990 Chevy Caprice factory radio. Remove the radio retaining screws. Remove the wiring harness and the antenna cable from the back of the radio.
