0
On a 1987 Jeep Grand Cherokee what could cause the blinkers to stop working?
Wiki User
∙ 12y ago
Check the Flasher, its usually located under the dashboard on the drivers side. its the thing that makes the clicking noise when you use your turn signals. Go to your local auto parts store and tell them about your blinker not working, they can help you get the correct flasher and tell you where its located. Be aware some vehicles have two of them.
If this isn't your problem, make sure all your bulbs are good, all the fuses are good and if that doesnt work call a mechanic because it could be the blinker stalk ( the thing you pull on when you use your blinker) or a wiring problem
Wiki User
∙ 12y ago
Wiki User
∙ 19y agoIt sounds like you are loosing voltage from the light switch to the tail lights. You just have to start tracing wires and checking splices. You may need a wiring diagram from MOTORLIT.COM.
Wiki User
∙ 11y agoshort or blown fuse, trailer connection is first place to check
Add your answer:
Earn +20 pts
What would cause the drivers window in your 99 jeep grand Cherokee to grind and then stop working?
It could be that the window motor has stopped working.
What would cause a fuel gauge to stop working on a jeep grand Cherokee 1999?
Bad sending unit in tank.
What cause wheel hop in a 1996 jeep grand Cherokee?
transfer case
Why doesnt the driver information center on 1993 jeep grand Cherokee work?
There are several things that can cause your 1993 Jeep Grand Cherokee driver information Center not to work. The most common cause is a blown fuse.
What would cause a 1994 Jeep Grand Cherokee Laredo transmission to overheat?
Pinched or blocked transmission cooling lines
What would cause the drivers window in your 99 jeep grand Cherokee to grind and then stop working?
It could be that the window motor has stopped working.
What causes the Blinkers to stopped working in a 2001 grand am?
There could be numerous problems that may cause this fault. Personally, my blinkers started going out (working sometimes and sometimes not) and what I found out is this...The flasher switch that is located in the dashboard above the radio is faulty. When my blinkers do not work i just tap down on the flasher switch without turning it on and my blinkers work again. Shotty electrical work in this car if ya ask me.
What would cause a fuel gauge to stop working on a jeep grand Cherokee 1999?
Bad sending unit in tank.
Could fuel injectors cause a misfire on 1998 jeep grand Cherokee?
Yes they can, if one or more are either stuck open or not working at all it will cause a misfire.
What cause wheel hop in a 1996 jeep grand Cherokee?
transfer case
Why doesnt the driver information center on 1993 jeep grand Cherokee work?
There are several things that can cause your 1993 Jeep Grand Cherokee driver information Center not to work. The most common cause is a blown fuse.
Why does your 1994 jeep grand Cherokee make a loud clicking noise when you drive it?
There can be several things that will cause your 1994 Jeep grand Cherokee to make a loud clanking noise when you drive it. The most common cause is a bad u-joint.
What would cause a 1999 Jeep Grand Cherokee to have no ac to front?
if the rear ac is working then you probably have a damper door that is inoperative. this is in the heater/evaporator box. so if it isn't working then you will be heating and cooling at the same time out of the heater box.
Will a 1990 Jeep Cherokee transmission fit on a 1997 Jeep Grand Cherokee?
no it wont fit cause ive just changed a 1990 jeep Cherokee transmission it had a 1998 jeep grand Cherokee transmission in it it broke the fly wheel and burned the torque converter up
What would cause quick flashing on only the right turn signal on a Jeep Cherokee?
Check two things: 1) the fuse for your flashers/blinkers and 2) that the bulbs are good still.
How do you repair non working blinkers on 1998 mercury Sable?
You have to diagnose the system to determine the cause. Check the fuses, the bulbs, the flasher relay then the switch.
What would cause your jeep grand Cherokee to turn over but not start?
Bad crank position sensor
