0
Whenever I try to tighten the G string on my new ukulele it never stays there it quickly turns back to its previous position what can I do?
Wiki User
∙ 14y ago
Is there a screw on the end of the tuning knob? Tightening it will help hold it in place. Don't over tighten!
If it is a friction peg with no screw at the end, you might try roughing up the pin a bit with some fine sandpaper.
It is possible you would have to replace the tuning pegs. A new set can be obtained for anywhere from $10 to over $100, depending on the quality and style you want. Most of the inexpensive ones will work just fine.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you tighten a door mirror on a 1979 Corvette?
remove the window to get access to the nuts remove them then the mirrors look in the pillars an tighten them up.
How does one tighten the folding mechanism of the side view mirror on a 2000 Jeep Grand Cherokee LTD?
Cannot be tighten, replace the mirror assy..
Original artist tighten up by black eyed peas?
Tighten Up was written by Archie Bell and Billy Buttier, (Archie and the Bells),and was performed originally by The Black Keys.
How does a harmonic balancer loosen itself on a 97 Jeep Grand Cherokee 4.0 in-line six and which way does the bolt turn to tighten and can you re-tighten it with standard tools?
Under normal circumstances it will not loosen. You use a torque wrench to tighten it to specifications. Specifications are located in the Haynes repair manual available from www.amazon.com. clockwise to tighten counterclockwise to loosen You need a socket that fits tightly on the bolt head and a long-handled torque wrench.
How do you change the sound of a bass drum?
You can tune a bass drum by turning.the knobs to the right to tighten or left to loosen on the rim of the drum. Loosen it for a lower pitch, tighten for higher pitch.
How do you tighten a loose battery cable?
Use the appropriate socket on the nut and tighten it. Make sure the cable is in the correct position first.
Where is the AC tension pulley for a 2000 Chevy Metro?
you dont adjust a tension pulley you adjust the position of the compressor to tighten the belt
How do you tighten a motorcycle chain?
loosen the adjustors on the swing arm next to the tire and pull the tire back and have someone hold the tire in position
How do you tighten the latch on a 2008 Chevy Equinox ls it looks like the previous owner shut something in it and now it is a little off how do you fix this?
Bend it back or get a new latch.
How do you perform a valve adjustment on a 3412 caterpillar?
You can perform a valve adjustment, on your 3412 Caterpillar diesel engine, by rolling the engine to the number one position. Tighten the valve adjustment screw. You will need to do this for each piston position.
How do you fix windshield wipers up on a 2000 Buick Regal that park in the up position?
Could be out of synk need to loosen and reset then tighten back up
How do you tighten the steering?
To tighten the steering you just tighten the nut under it and then your done. NICE
What is the rocker arm torque specs and sequence for a Chevy 305?
With the valve fully closed and the lifter fully at the down position, tighten the adjusting nut until there is no up and down travel in the push rod. Then tighten the adjusting nut 1/4 turn. This is only if you have hydraulic lifters. Tighten the rocker studs to 50 ft/lb of torque. These are the bolts holding the rocker assembly in place.
Do you need sealant to install a new valve cover gasket?
no the gasket should be rubber and should be bendable all you do is install it in the correct position and tighten the bolts in the right sequence
How do you tighten a binder ring?
take out the silver circle then it will tighten
How do you tighten the fan belt on a peugeot 205?
just in front of the altenator, there is a 10mm bolt, tighten that and it will tighten the fan belt
Once the TV is mounted how easy is it to tilt it. Is it easy to adjust or is it very tight?
Adjusting the tilt of the TV is relatively easy. Once you adjust the tilt to the desired level, you can then tighten it to remain at that position.
