0
What else can I help you with?
Can you put a dimmer switch on a combination of halogen and incandescent fixtures?
Yes, you can use a dimmer switch with a combination of halogen and incandescent fixtures. However, it's essential to make sure that the dimmer switch is compatible with both types of bulbs to avoid any potential issues such as flickering or buzzing. Additionally, double-check the wattage rating of the dimmer switch to ensure it can handle the combined load of the fixtures.
What happens to a non dimmable lamp if used on a dimmer?
If you use a non-dimmable Compact Fluorescent Lamp (CFL) in a circuit controlled by a dimmer switch no damage will be done but the CFL will stay bright when the dimmer is turned down whilst any other normal incandescent lamps wired into the same circuit will go dim in the normal way.Dimmable Compact Fluorescent Lamps are now available, for example in the Megaman range of CFLs. For more information see the Related Link shown below.Incandescent dimming uses any incandescent lamps and an incandescent dimmer.To dim fluorescent lamps usually requires use of fluorescent dimmers AND fluorescent dimmable ballasts. If these two components do not match, dimming will not work.The fluorescent lamps themselves are the same whether you put them in a standard (nondimming) ballast or a dimmable ballast.If your dimmers are not dimming the CFLs they are either not fluorescent dimmers or, more likely, your ballast in the light fixture is not a dimmable ballast.
Can you put an AC dimmer switch on a low voltage 12 volt halogen light fixture?
Although a dimmer can be designed for 12 v halogen lamps it is more common for dimmers to work on higher voltages. Dimmers have to work into a resistive load so it is not usually possible to place the dimmer on the high-voltage side of the 12 v transformer that comes with the lights.
If one switch controls a fan and a light but the dimmer part for the light does not work and the switch gets warm after a while what could be the problem?
I'm going to assume that the switch that's getting warm is the dimmer. Even when a dimmer is working correctly it gets warm and that's just the electronic parts of it. The face of a dimmer is actually a heat sink to help remove excess heat. If you swap out the dimmer you will likely find your problem is resolved. Remember to de-energize the circuit by turning off the breaker before working on it. If in any doubt, consult a qualified electrician. Andy Be aware that a dimmer for lights does NOT work for fans (though it may sometimes appear to work, you can end up with noise, problems such as the light attached to the fan not working, the dimmer getting overheated, etc). So even though it might seem to work at first, you'll have problems, and it's against code to put the wrong kind of dimmer there. You can purchase a dimmer which is rated for ceiling fans at Home Depot or Lowes, but they are more expensive than light switch dimmers. Of course, if there is a single on/off switch at the wall which controls the fan and its light, then you might be better off buying a remote control unit to install in the fan - it will allow you to dim the fan and light separately (and safely). Or purchase a new fan with a remote... ceiling fans are cheap enough now that if yours is old enough, it might be a nice time for an update.
Can dimmer switches be used with 3 way switches?
Well, they sell 3-way compact fluorescent bulbs, but they're quite a bit more expensive; up to 20 dollars a bulb!...Harder to find as well, since many people (myself included) debate whether the purchase is worth it. I've made the switch w/ all but my three-way lamp. Anyway, using a one-way cf bulb will pose the same problems as using an incandescent one-way as far as electrical fire hazards. Hope that helps!See the answer to the Related Question by clicking the link shown below.
How can you put a dimmer on a 3-way switch?
To put a dimmer on a 3-way switch, you will need to replace one of the existing switches with a 3-way dimmer switch. This dimmer switch is designed to work with the other 3-way switch to control the light's brightness. Make sure to follow the manufacturer's instructions and turn off the power before attempting any electrical work.
Can you put a dimmer switch on compact fluorescent light bulbs?
I have but if dimmer is on low the light fixture sometimes "hums", can be anoying It also shortens the bulb life, significantly in some cases. But their are also CFL bulbs built to be used with a dimmer switch that avoid these problems.Another AnswerYou should only use CFLs specifically-designed to be used with dimmers in circuits controlled by dimmer switches. There is a proven danger of fire hazard when ordinary CFLs are controlled by dimmer switches and, so, this should NEVER be done.
Are halogen lights able to be put on a dimmer switch?
Yes. There are various types of dimmers. Look for the halogen dimmer in your favorite search engine.
Why does your clockradio light switch off when the headlights are put on?
They as designed to "dim" when headlights are on to reduce "glare" try adjusting dash dimmer switch
How many downlights can you put on 240v single phase c10 mcb operated by a 3-pole dimmer switch?
need to know the capacity of the dimmer and the size of the lights
Can you put a dimmer switch on a combination of halogen and incandescent fixtures?
Yes, you can use a dimmer switch with a combination of halogen and incandescent fixtures. However, it's essential to make sure that the dimmer switch is compatible with both types of bulbs to avoid any potential issues such as flickering or buzzing. Additionally, double-check the wattage rating of the dimmer switch to ensure it can handle the combined load of the fixtures.
Energy savings light bulbs flickering and do not dim on dimmer switch?
you can not put a normal dimmer on a florescent light. You need to install a dimmer made for flourecent lights and they are expensive about 50 dollar around here. If you want to dim it put a normal incandescent bulb in the fixture.
Why would T100 not have high beam lights?
try your dimmer switch just put one in my 97 that was my problem
Can you put a dimmer switch on a Christmas tree?
on some i think you can there will be 2 switches on a panel bord and 1 will be dimmer then the other or on other trees there are different patterns some dim some very bright
What happens to a non dimmable lamp if used on a dimmer?
If you use a non-dimmable Compact Fluorescent Lamp (CFL) in a circuit controlled by a dimmer switch no damage will be done but the CFL will stay bright when the dimmer is turned down whilst any other normal incandescent lamps wired into the same circuit will go dim in the normal way.Dimmable Compact Fluorescent Lamps are now available, for example in the Megaman range of CFLs. For more information see the Related Link shown below.Incandescent dimming uses any incandescent lamps and an incandescent dimmer.To dim fluorescent lamps usually requires use of fluorescent dimmers AND fluorescent dimmable ballasts. If these two components do not match, dimming will not work.The fluorescent lamps themselves are the same whether you put them in a standard (nondimming) ballast or a dimmable ballast.If your dimmers are not dimming the CFLs they are either not fluorescent dimmers or, more likely, your ballast in the light fixture is not a dimmable ballast.
Can you put a black light tube into any fluorescent fixture?
No, not all fluorescent fixtures are suitable for black light tubes. Make sure the fixture is compatible with the specific type and size of black light tube you want to use, as some fixtures are designed for specific types of fluorescent tubes and may not work properly with others. It is recommended to check the fixture specifications to ensure compatibility before installing the black light tube.
I am removing a dimmer switch to put in a regular switch but there are two incoming hot wires what do i do?
The regular switch just connects in the circuit the same way as the dimmer switch came out. If the dimmer switch had its own wires the only difference will be is you will have to supply your own wires from the new switch to the existing connection. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.
