0
What else can I help you with?
What is a Circuit breaker and explain type circuit breakers?
A circuit breaker is a switching device which can make,brake and carrying (or trip the circuit) that specified over currents for a small interval of time . There is a different types of Circuit Breaker's are there 1.According to their arc quenching media these are divided into 4 types a) Oil circuit breaker b) Air blast circuit breaker c) SF6 circuit breaker d) vacuum circuit breaker 2. According to their services the circuit breaker can be divided as a) Outdoor Circuit Breaker b) Indoor Breaker 3. According to the operating mechanism of circuit breaker they can be divided as a) Spring operated Circuit Breaker b) Pneumatic Circuit Breaker c) Hydrolic Circuit Breaker 4. According to the voltage level of installation these are divided into 3 types a) High Voltage Circuit Breaker b) Medium Voltage Circuit Breaker c) Low Voltage Circuit Breaker.
What size breaker for a 208 volt single phase motor that pulls 1.4 amps?
208 volts is not a common single phase voltage but you could just size your breaker to the capabilities of the conductor. 208 is normally a phase to phase voltage <<>> Many 230 volt motors can be connected to lower voltage supplies. These motors can be connected to supplies of 208 and 200 volts. The code requirement is that the 230 volt full load amperage of the motor be increased by 10% and 15% respectively for wire sizing and breaker selection. To answer the question you will need a two pole 15 amp breaker.
How can a 30 Amps fuse for a shower of 9.5KW be replace with a 40 Amps fuse on RCD trip?
If the current safety requirement is 30 amps, you can;t run if off of a larger circuit breaker. It violates NEC and is very unsafe. If the current requirement is 40 amps , it will continuously trip a 30 amp breaker because it is too small of a breaker in electrical requirement.
A small appliance circuit will be protected by a circuit breaker rated at?
Yes, it will be protected by a circuit breaker or fuse. The normal rating of the circuit breaker or fuse is 25% more than the maximum current expected, or the maximum current allowed for the cable size, whichever is lower.
Can you plug equipment rated for 50A into a 30A circuit?
Yes, with a caveat. The 50A wire and plug is more than heavy enough for the dryer, so there is no problem there. The possible problem is that the dryer is designed to be protected by a 30A breaker. In the event of failure in the dryer, the breaker may not trip as it is oversized. The best solution? Get a small breaker box from a home center and mount a 30A breaker in it. Mount it on the back of the dryer, run the 50A cord into the feed lugs of the box, and connect the dryer feed to the 30A breaker. This way you can plug the dryer into the 50A outlet like you want, and the dryer is protected with a 30A breaker as usual. You can get small breaker boxes or fused disconnects without too much cost. Just make sure the breaker box / disconnect panel is rated to 50A, as you want to feed it off a 50A circuit. As long as the voltage requirement of the dryer matches the voltage of the outlet (which is presumably 240 volts), then yes. The amp rating of the cord and outlet is merely the maximun current (amps) allowed. You're well under that with 24 amps.
What is a Circuit breaker and explain type circuit breakers?
A circuit breaker is a switching device which can make,brake and carrying (or trip the circuit) that specified over currents for a small interval of time . There is a different types of Circuit Breaker's are there 1.According to their arc quenching media these are divided into 4 types a) Oil circuit breaker b) Air blast circuit breaker c) SF6 circuit breaker d) vacuum circuit breaker 2. According to their services the circuit breaker can be divided as a) Outdoor Circuit Breaker b) Indoor Breaker 3. According to the operating mechanism of circuit breaker they can be divided as a) Spring operated Circuit Breaker b) Pneumatic Circuit Breaker c) Hydrolic Circuit Breaker 4. According to the voltage level of installation these are divided into 3 types a) High Voltage Circuit Breaker b) Medium Voltage Circuit Breaker c) Low Voltage Circuit Breaker.
What happens to voltage during a short to ground?
Basically, the same as if you had a short to neutral, since the neutral and ground are tied to the same bus bar in the breaker panel. The breaker should trip, or the fuse should blow. Supply of voltage then stops.See the answer to the Related Question about GFCIs - shown below - for information about circuit protection when even a small current flows to ground.
What is meant by the term small signal amplifier?
Small signal amplifiers are generally referred to as "Voltage" amplifiers as they convert a small input voltage into a much larger output voltage.
What is the effect of overvoltage on small electric loads?
The effect of modest over voltage on any type of load is added heat and higher current flow . As the voltage increases past modest an arc will eventually happen.
What is the purpose of a small step down transformer in electrical circuits?
A small step-down transformer in electrical circuits is used to reduce the voltage from a higher level to a lower level. This helps to safely power devices that require lower voltage levels, protecting them from potential damage.
What size breaker for a 208 volt single phase motor that pulls 1.4 amps?
208 volts is not a common single phase voltage but you could just size your breaker to the capabilities of the conductor. 208 is normally a phase to phase voltage <<>> Many 230 volt motors can be connected to lower voltage supplies. These motors can be connected to supplies of 208 and 200 volts. The code requirement is that the 230 volt full load amperage of the motor be increased by 10% and 15% respectively for wire sizing and breaker selection. To answer the question you will need a two pole 15 amp breaker.
How do you change voltage regulator in 1989 ford f-150?
It is on the back of the alternator, Disconnect the Battery first!. There is a small module on the back of alternator remove and replace.
Domestic installation power circuit in small building diagrams?
There is no standard diagram for a small domestic building power circuit. The power needs of the building will determine the size of the breaker box and voltage needed. Local electrical codes will also change the way that the building is wired.
How can a 30 Amps fuse for a shower of 9.5KW be replace with a 40 Amps fuse on RCD trip?
If the current safety requirement is 30 amps, you can;t run if off of a larger circuit breaker. It violates NEC and is very unsafe. If the current requirement is 40 amps , it will continuously trip a 30 amp breaker because it is too small of a breaker in electrical requirement.
Why should someone generate power at 220 V?
Only small personal generators generate a voltage of 220 volts. This level of voltage is used usually during power outages. For voltages that power the electrical grid, the voltage is generated at a much higher voltage and then transformed by the use of transformers, into the voltage that is required by different distribution services.
Will a LED shine brighter if it is connected to a higher voltage?
A LED has a forward voltage drop dependent on it's composition. It is fairly constant within a small range of current flow. If the voltage is too high and the current is not limited, the LED will burn out. The brightness can be varied by varying the available current, but the voltage across the LED remains virtually the same.
Why does a 20 amp breaker blow when it is only hooked up to a 100 watt bulb a small pump for a fish pond and a household freezer?
Either there is something drawing a lot more current, or the breaker is faulty. You may need to have an electrician check the breaker for you, or if you feel competent, replace the breaker with another of equal value. That would be a lot less expensive than having an electrician drop by. BUT... The startup current of a household freezer AND the "small pump" may add up to enough current that it's tripping the breaker. Read the labels and see what the actual current draw is on the pump AND on the freezer. If the total current approaches the value of the breaker it might be best to move something to a different circuit.
