Using a 12v 600ma source is allowing 12 volts and 600 amps of power. If the device requires a 12v 500ma source, the larger source is acceptable. Please note that it will only be drawing on 500ma of the available 600ma.
i am not sure, BUT according to the answer in this post:Can_you_use_a_9V_600mA_adapter_on_a_9V_400ma_scanneryou need an adaptor of 9v and AT LEAST 500mA (assuming that the appliance draws 500mA)
Using a 12V 500mA power supply instead of a 12V 300mA power supply will likely be fine as long as the voltage matches, but the higher current capacity (500mA) means the power supply can deliver more current if needed by the device. The device will only draw the current it needs, so having a higher current capacity power supply should not cause any issues.
If the camera actually uses 700 mA in order to do its job, then the 500 mA adaptor will warm up, then overheat, and eventually fail.
No.If it is AC output, it will blow out the power circuits of the DC device.If it is DC output, it doesn't have enough current capacity for the load of the DC device.If you want to power a DC device with a wall wart, make sure the wart is:DC outputCorrect polarity (some have reversible polarity)Exact same voltage as the deviceGreater than or equal to current rating of the device
Not for very long. If the device actually requires 2A in order to do its job, then the adapter ... which is only designed to deliver 0.5A or less ... will get warm, then overheat, and then fail. Possibly in as little as a few seconds.
i am not sure, BUT according to the answer in this post:Can_you_use_a_9V_600mA_adapter_on_a_9V_400ma_scanneryou need an adaptor of 9v and AT LEAST 500mA (assuming that the appliance draws 500mA)
Using a 600mA adaptor instead of a 500mA one could potentially supply more current to the device than it is designed for. Depending on the device's circuitry, this can lead to overheating and damage, especially if the device is not designed to handle the extra current. It's generally safer to use an adaptor with the recommended current rating for the device.
Using a 12V 500mA power supply instead of a 12V 300mA power supply will likely be fine as long as the voltage matches, but the higher current capacity (500mA) means the power supply can deliver more current if needed by the device. The device will only draw the current it needs, so having a higher current capacity power supply should not cause any issues.
yes this will work fine
You can use any 9v adapter as long as the output amperage is rated higher than the amperage rating of your appliance so yes a 600ma adapter can be used to power a 500ma or 400ma appliance
12v 1000mA means that the maximum output of that unit is 1000 milliamps at 12 volts. 12v 150 mA means that the maximum output of that unit is 150 milliamps at 12 volts. So if you need 150 milliamps at 12v either will do. BUT if you need over 150 milliamps at 12v then you must go for the 1000 mA unit. By the way there are 1000 milliamps in 1 amp.
If the camera actually uses 700 mA in order to do its job, then the 500 mA adaptor will warm up, then overheat, and eventually fail.
Yes, you can use a 500mA (0.5A) supply instead of a 1A supply, but it depends on the requirements of your device. If the device draws more than 500mA, it may not function properly or could be damaged due to insufficient current. Always ensure that the power supply can meet the current demands of your application for safe and effective operation.
No.If it is AC output, it will blow out the power circuits of the DC device.If it is DC output, it doesn't have enough current capacity for the load of the DC device.If you want to power a DC device with a wall wart, make sure the wart is:DC outputCorrect polarity (some have reversible polarity)Exact same voltage as the deviceGreater than or equal to current rating of the device
A 12v AC adapter can be use to power devices that requires 12VDC and up to 500mA. It can also be use with electrical devices that require power but do not contain internal components to derive the required voltage and power from the main power.
Yes you can. But it may damage your computers power supply.
As long as the batteries are putting out the exact same voltage, then yes you can use a battery with a higher ma rating.