answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

Does a shunt trip breaker work from a dry set of contacts?

Yes, but you need a power source, for the shunt trip coil voltage, in the circuit.


How do you wire a shunt trip breaker so you can test trip it?

There are per-engineered shunt trip solutions such as the Littelfuse LPSM that have a transformer that isolates the line voltage from the control voltage. You simply wire the N.O. contact on the float in the shunt trip isolated contacts.


Can you put a 50 amp beaker in a 60 amp panel?

I've never heard of a 50 amp b-e-a-k-e-r. You can put a 50 amp b-r- e-a-k-e-r in a 60 amp panel; but you can only have an additional 10 amp breaker along with it. You may need to consider adding another larger panel or a separate 50 amp breaker box.


How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?

Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.


Do you need to use some type of mini breaker panel with a single 15A circuit breaker to connect a 15A receptacle into a 30A line?

Yes, you need to use a mini breaker panel with a 15A circuit breaker to safely connect a 15A receptacle to a 30A line. The breaker panel will protect the receptacle and wiring from the higher current capacity of the 30A line, preventing potential overheating or damage. It's important to match the amperage of the circuit breaker with the rating of the receptacle to ensure safe electrical operation.

Related Questions

Does a shunt trip breaker work from a dry set of contacts?

Yes, but you need a power source, for the shunt trip coil voltage, in the circuit.


Why do you need a shunt trip breaker?

A shunt trip breaker is installed like any other molded case breaker. The only difference is that it has an internal tripping coil that is usually connected to a C.T. The breaker is usually mounted in a MCC cabinet The top of the breaker is bolted to the MCC bus bars and the bottom of the breaker is connected to the load. The load conductors pass through the C.T.'s which induces a current into the circuit to trip the tripping coil in the breaker.


How do you wire a shunt trip breaker so you can test trip it?

There are per-engineered shunt trip solutions such as the Littelfuse LPSM that have a transformer that isolates the line voltage from the control voltage. You simply wire the N.O. contact on the float in the shunt trip isolated contacts.


How is a Tee Cardiac Shunt preformed?

A TEE is a transesophageal echo, which is a diagnostic test. A cardiac shunt is a separate thing altogether, as it is surgery. Perhaps they performed a TEE and as a result, felt there was a need to proceed further and explore the need for a shunt?


How do you hook up wire from ansul system to shunt trip breaker?

You would need to take the "input" wire for the shunt trip breaker to an electrical switch (not alarm initiating switch, which are DC voltage rated) within the Automan unit and connect to the "Common" connection and the "return", the wire to the actual shunt circuit of the breaker, from the "Normally Open" connection of the switch. When the unit activates, the switch will be placed into "Closed" position, therefore completing the circuit and activating the shunt coil.


What is the compatibility of a Square D 125 amp breaker with my electrical panel?

To determine the compatibility of a Square D 125 amp breaker with your electrical panel, you need to check the manufacturer's specifications for your panel to see if it is rated to handle a 125 amp breaker. It is important to ensure that the breaker is compatible with the panel to avoid any safety hazards or damage to the electrical system.


How do you connect 480volt and coil to fire alarm system?

I can only assume that you are attempting to connect 480VAC coil from a elevator to a fire system in order to shunt the elevator. In order to do this you will need a shunt trip breaker rated for this use.


Can you put a 50 amp beaker in a 60 amp panel?

I've never heard of a 50 amp b-e-a-k-e-r. You can put a 50 amp b-r- e-a-k-e-r in a 60 amp panel; but you can only have an additional 10 amp breaker along with it. You may need to consider adding another larger panel or a separate 50 amp breaker box.


I have a Transformer 480 primary 208 secondary feeding 1 200amp mb 42 space panel I need to feed a subpanel 6 ft away I'm thinkin feed through lug at top of bus or at feed through MB suggestions?

The sub-panel need to be fed from the main panel, by way of a circuit breaker connected to one of the breaker locations. Or if your sub-panel has a main breaker installed you can feed from the main panel with a sub-feed lug kit. This looks like a breaker, but is only a point where you can branch off the sub panel.


How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?

Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.


How do I go about installing a 50 amp breaker in my electrical panel?

To install a 50 amp breaker in your electrical panel, you will need to first turn off the power to the panel. Then, remove the panel cover and locate an open slot for the new breaker. Connect the hot wire to the breaker, the neutral wire to the neutral bar, and the ground wire to the ground bar. Secure the breaker in place and replace the panel cover. It is recommended to consult a licensed electrician for assistance to ensure safety and compliance with local codes.


What type of breaker do I need for my electrical panel?

You will need to determine the specific type of breaker required for your electrical panel based on the manufacturer's specifications and the electrical load requirements of your home. It is recommended to consult a licensed electrician for proper guidance and installation.