0
What else can I help you with?
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
Can a 40 amp breaker not a 4 amp breaker be used to replace a 35 amp breaker for ac unit?
No, it is not recommended to replace a 35 amp breaker with a 40 amp breaker for an AC unit. Breakers are designed to protect the circuit and the equipment, so using a higher rated breaker can lead to overheating and potential damage. It is best to use the correct amperage rated breaker for the equipment.
Is the wire running to a 20amp breaker different from a wire running to a15amp breaker?
Yes, a 20 amp breaker requires AWG # 12 copper wire. A 15 amp breaker requires AWG # 14 copper wire.
Can I you use existing 8 3 wire hooked to a 30amp breaker was hooked to old electric heater to wire a heater that requires 10 2 wire its a 5000watt 240volt heater?
No, you cannot use an existing 8 3 wire hooked to a 30amp breaker for a heater that requires 10 2 wire. The wire gauge and breaker size need to match the specific requirements of the new heater to ensure safety and proper function. You will need to upgrade the wiring to accommodate the 10 2 wire needed for the 5000-watt 240-volt heater.
What is the purpose of the third wire?
By "third wire" I believe you are speaking of the ground wire. Its only purpose is to ensure that the over-current device, which is the breaker or fuse, operates property when a fault exists in the circuit. Without the ground wire you increase your risk of injury, death, or property damage. It is there for your protection. Do not remove it. Always choose to use it when it exists.
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
Can a 40 amp breaker not a 4 amp breaker be used to replace a 35 amp breaker for ac unit?
No, it is not recommended to replace a 35 amp breaker with a 40 amp breaker for an AC unit. Breakers are designed to protect the circuit and the equipment, so using a higher rated breaker can lead to overheating and potential damage. It is best to use the correct amperage rated breaker for the equipment.
How do you wire a 277 to 120 volt transformer?
The voltage 277 volts is a three phase line to neutral voltage of a 480 volt system. What is needed for the protection of the transformer is a two pole breaker from the 480 volt CDP (Central Distribution Panel). The breaker will be sized to the KVA of the transformer. The wire will be sized to the breaker plus 25%. The electrical code requires that on motor and transformer feeders, they be sized to 125% of the total current capacity of the equipment.
What is the cable size for 7.5kw slit system air conditioner?
The wire is sized to the maximum overcurrent protection device (Max circuit breaker) ampacity. This is listed on the nameplate of the outdoor condensing unit. Size the wire to match the breaker.
How do you wire a 15 amp breaker?
Ground wire connects to the ground bar, white wire connects to the neutral bar, and black wire connects to the breaker. Be sure and turn off main breaker before installing the wire or the breaker.
How do you change wire fuse for circuit breaker?
A circuit breaker does not have a wire fuse in it.
Is the wire running to a 20amp breaker different from a wire running to a15amp breaker?
Yes, a 20 amp breaker requires AWG # 12 copper wire. A 15 amp breaker requires AWG # 14 copper wire.
Can I you use existing 8 3 wire hooked to a 30amp breaker was hooked to old electric heater to wire a heater that requires 10 2 wire its a 5000watt 240volt heater?
No, you cannot use an existing 8 3 wire hooked to a 30amp breaker for a heater that requires 10 2 wire. The wire gauge and breaker size need to match the specific requirements of the new heater to ensure safety and proper function. You will need to upgrade the wiring to accommodate the 10 2 wire needed for the 5000-watt 240-volt heater.
What is the purpose of the third wire?
By "third wire" I believe you are speaking of the ground wire. Its only purpose is to ensure that the over-current device, which is the breaker or fuse, operates property when a fault exists in the circuit. Without the ground wire you increase your risk of injury, death, or property damage. It is there for your protection. Do not remove it. Always choose to use it when it exists.
How do you wire an AFCI breaker?
To wire an AFCI breaker, first turn off the power to the circuit. Then, connect the hot wire to the breaker's terminal, the neutral wire to the neutral bar, and the ground wire to the ground bar. Finally, snap the breaker into place in the electrical panel.
How do you tell if a wire is shorted out?
If a wire is shorted out, you may notice sparks, smoke, or a burning smell coming from the wire. You can also use a multimeter to test for continuity between the two ends of the wire - if there is continuity, it indicates a short circuit.
How a 240 V GFCI breaker works without a neutral ran to the equipment?
A 240V GFCI breaker monitors the difference in current between the hot wires, providing ground-fault protection without needing a neutral wire. It compares the current on both hot wires and trips if an imbalance is detected, indicating a ground fault. This system does not rely on a neutral wire to detect faults and protect against electrical shocks.
