0
What else can I help you with?
How will an electrical circuit behave if there is a short in the circuit?
If it is a properly wired circuit (according to code) in the home, the breaker for that circuit will trip deenergizing the shorted circuit. If it is not properly wired, it could get hot and start a fire and possibly burn down the home.
Why does the breaker continue to trip until hot wire is disconnected?
There is a short somewhere in the line. Start at the outlet end and what is plugged into it and work your way back. If it is a GFI breaker, they can be bad and trip as soon as any drain is put on them. I have had them trip as soon as a drill is plugged in without even turning on the drill.
What is a 15 amp double pole breaker?
A double pole breaker has one pole attached to one side of your breaker panel's bus or hot leg, and another pole attached to another hot leg or bus, if it is in a residential panel (in the US) each leg of the breaker is 120 volts to ground or neutral and 240 hot leg to hot leg. The 15 amp indicates that the breaker will trip if the circuit exceeds 15 amps across the two outputs of the breaker.
Is it safe to trip a breaker by touching the hot wire to the ground wire if you cannot identify the correct breaker?
This is one way that can locate hidden circuit breakers. It is not the best way because an arc flash could result if the breaker does not trip. An arc flash can generate enough heat instantaneously to burn the flesh off of any exposed skin. If there is combustible products or combustible air mixture that is in the general location of the arc, a fire could be easily started. The way that I do it is to load the circuit. I have a 3000 watt heater that I plug in to the circuit that I am trying to locate the breaker for. This loads the 15 amp circuit to 25 amps. The circuit breaker is located in a few seconds.
An open circuit results when a hot wire touches ground?
An open circuit occurs when there is a break in the electrical path, cutting off the flow of current. When a hot wire touches ground, it can create a short circuit where current flows directly to ground instead of through the intended circuit, leading to potential danger and damage to the equipment.
Why is the breaker hot?
The breaker is hot because it is designed to trip and disconnect the electrical circuit when there is an overload or short circuit, causing it to generate heat as it operates.
Why does the circuit breaker keep tripping immediately?
The circuit breaker may keep tripping immediately due to a short circuit, which occurs when a hot wire comes into contact with a neutral wire or ground wire. This causes a sudden surge of electricity, triggering the circuit breaker to trip for safety reasons.
Why is the circuit breaker getting hot without tripping?
The circuit breaker may be getting hot without tripping due to an overload or a faulty connection in the circuit. This can cause excessive heat buildup, which the breaker may not detect as a high enough current to trip. It is important to address this issue promptly to prevent potential fire hazards.
Is it normal for a circuit breaker to feel hot to the touch?
No, it is not normal for a circuit breaker to feel hot to the touch. If a circuit breaker feels hot, it may indicate an issue with the electrical system that should be addressed by a professional electrician.
Why would a hot wire go directly from the breaker to the neutral bar?
If this is is exactly what you are seeing then the breaker will not be resettable. The breaker will instantaneously trip. If the identified conductor comes into the distribution panel from an external circuit then this is another scenario.
How will an electrical circuit behave if there is a short in the circuit?
If it is a properly wired circuit (according to code) in the home, the breaker for that circuit will trip deenergizing the shorted circuit. If it is not properly wired, it could get hot and start a fire and possibly burn down the home.
Why does the breaker continue to trip until hot wire is disconnected?
There is a short somewhere in the line. Start at the outlet end and what is plugged into it and work your way back. If it is a GFI breaker, they can be bad and trip as soon as any drain is put on them. I have had them trip as soon as a drill is plugged in without even turning on the drill.
What is caused when the hot wire and either the neutral or ground wire make contact?
A short circuit. If things are working as they should breaker will trip or fuse will blow.
What is a 15 amp double pole breaker?
A double pole breaker has one pole attached to one side of your breaker panel's bus or hot leg, and another pole attached to another hot leg or bus, if it is in a residential panel (in the US) each leg of the breaker is 120 volts to ground or neutral and 240 hot leg to hot leg. The 15 amp indicates that the breaker will trip if the circuit exceeds 15 amps across the two outputs of the breaker.
Is it safe to trip a breaker by touching the hot wire to the ground wire if you cannot identify the correct breaker?
This is one way that can locate hidden circuit breakers. It is not the best way because an arc flash could result if the breaker does not trip. An arc flash can generate enough heat instantaneously to burn the flesh off of any exposed skin. If there is combustible products or combustible air mixture that is in the general location of the arc, a fire could be easily started. The way that I do it is to load the circuit. I have a 3000 watt heater that I plug in to the circuit that I am trying to locate the breaker for. This loads the 15 amp circuit to 25 amps. The circuit breaker is located in a few seconds.
Where is the circuit breaker for a hot water heater?
The best way to determine which circuit breaker is for the water heater is with a voltage meter, It is suppose to be only one circuit breaker, but in a faulty application it could be two breakers
Why tap in your house gives shock when it is touched or used?
Your water system is not grounded. Turn the main breaker in your distribution panel to off and ground the water system. If a "hot" wire has come into contact with the plumbing, when you turn the electrical panel main breaker back on a breaker will trip. This will give you the circuit that is at fault and a place to start looking for the short circuit.
