0
What else can I help you with?
What's a double breaker 20 amps and 30 amps?
A double breaker is a breaker that has 2 switches on it. One of the switches is 20 amps and the other is 30 amps.
Does a double 50 amp breaker make a 100 amp?
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
Can a 220 VAC breaker be single pole or does it have to always be a double pole breaker?
A 220 VAC breaker can be single pole or double pole depending on the application. For standard 220 VAC circuits like most household appliances, a double pole breaker is typically used. However, in certain situations where only one hot wire is needed, a single pole breaker can be used for 220 VAC circuits.
How many 30amp slots in a breaker box are needed for 240v cook top?
You would need one 30 amp double-pole breaker in the breaker box for a 240V cooktop.
What is a 15 amp double pole breaker?
A double pole breaker has one pole attached to one side of your breaker panel's bus or hot leg, and another pole attached to another hot leg or bus, if it is in a residential panel (in the US) each leg of the breaker is 120 volts to ground or neutral and 240 hot leg to hot leg. The 15 amp indicates that the breaker will trip if the circuit exceeds 15 amps across the two outputs of the breaker.
Is a double throw 15amp breaker the same as a 30 amp breaker amp?
You have a double pole breaker for 240Volt supply. The maximum current is 15 amp.
What's a double breaker 20 amps and 30 amps?
A double breaker is a breaker that has 2 switches on it. One of the switches is 20 amps and the other is 30 amps.
What is the appropriate double pole 30 amp breaker to use for a dryer installation?
The appropriate double pole 30 amp breaker to use for a dryer installation is a 30 amp double pole circuit breaker.
Does a double 50 amp breaker make a 100 amp?
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
What is the maximum amperage rating for a double breaker 20 amp?
The maximum amperage rating for a double breaker 20 amp is 20 amps.
3 phase panel double pole single throw breaker 2 wires from breaker going to lighted sign 120 volts each is this a 240 volt system or a 120 feeding 2 diff ballast in the sign?
In a three phase panel a double pole single throw breaker is definatly putting out 220v as two separate 110v circuits that are out of phase with each other. So from one leg to the other its 220v and from either leg to ground its 110v. By definition it is 220v but it could be used as separate 110v circuits as well. The only way to know how its actually being used would be to open up the sign and see if both circuits are tied into one ballast as 220v or if they split and go to differant ballasts then they are 110v circuits using a common disconnect means. Being that either way both circuits terminate in the same area they technically both require a double pole single throw breaker.
What size breaker should be used for a double oven?
50 amp breaker wired with AWG # 6 wire.
What is the maximum electrical load that can be handled by a 60 amp double pole breaker?
A 60 amp double pole breaker can handle a maximum electrical load of 60 amps.
What are the differences between a single pole and a double pole breaker?
A single pole breaker controls one wire and is used for 120-volt circuits, while a double pole breaker controls two wires and is used for 240-volt circuits.
Can a 220 VAC breaker be single pole or does it have to always be a double pole breaker?
A 220 VAC breaker can be single pole or double pole depending on the application. For standard 220 VAC circuits like most household appliances, a double pole breaker is typically used. However, in certain situations where only one hot wire is needed, a single pole breaker can be used for 220 VAC circuits.
Where is the double-pole circuit breaker located?
before the load
Is it a fire hazard to double land wires on a breaker?
Yes!
