answersLogoWhite

0

I have the same problem trying to figure out how to take it out seems that there must be a keeper that keeps it on the stainless shaft

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you change a hep-lock?

To change a hep-lock, first wash your hands and gather the necessary supplies. Clean the site with an alcohol swab and then remove the old hep-lock. Insert the new hep-lock using sterile technique and secure in place. Finally, flush the hep-lock with the appropriate solution.


Function of screw lock in Bunsen burner?

The screw lock in a Bunsen burner is used to control the airflow entering the burner. By adjusting the screw lock, you can regulate the amount of oxygen mixing with the gas, which in turn controls the size and type of flame produced by the burner.


How do you apply keypad lock pasword in lava KKT04 plus?

To set a keypad lock password on the Lava KKT04 Plus, go to the "Settings" menu from the home screen. Navigate to "Security" or "Phone Lock," then select the option to set or change the password. Enter your desired password, confirm it, and save the changes. Ensure to remember the password, as you will need it to unlock your phone.


How do you fix the rear door locks on a 1994 Mercury Topaz that will not unlock manually?

Most likely rust has settled in. The best way is to remove the door panel and spray all the parts with either a rust spray, or Wd40. If you cannot open the door to get the panels off, then roll down the window, and use an oil can and squirt oil all over the lock parts, and work the lock at the same time. Might take some time, and put a piece of carton under the door to catch all the oil. Good luck.


How does one lock the cell phone Razor?

Someone can lock the cell phone named Razor through two methods. To physically lock the device, the lock button can be used to lock the device. To lock the device to a specific carrier, software needs to be loaded onto the phone.

Related Questions

Can a 1998 mercury 200efi outboard vapor lock?

Yes a 1998 mercury 200 efi outboard vapor can lock. Most of the time the issue can be traced back to the quality of fuel put into the engine that can cause the vapor to lock.


How do you replace ignition lock cylinder on a 1996 Mercury Tracer?

Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.


In a 89 mercury grand marquis how do you ignition cylinder replacement?

how to change igntion lock


What year is a sea king outboard 3hp GG8962A 85X705837?

The GG8962A is a 1958 Montgomery Wards Sea King, also know as a Gale-OMC 3D15B. It is a 3hp single with a reverse lock.


How do you change the factory code for the door lock on a 1994 mercury grand marquis?

You cannot change the master code. You can add other codes, but you cannot change the master....


How do you get a key code or change ignition for a 1990 Mercury Sable?

Your Ford/Mercury dealer can get the code. See "Related Questions" below for instructions on changing the lock cylinder


How do you change the driver side power lock motor on a 1999 Mercury Sable Wagon?

If you remove door panel you should have access to unit


How do you unjam your letter lock?

Reverse the way you jammed it


WHY DOES MY 1998 mercury mystique only works in reverse and low gears?

Is it possible you're pressing the green "no overdrive" knob when you put the car in gear? This will lock-out higher gear range. Just a thought.


How do you install the headlights on a 2002 mercury mountaineer?

open the hood and access the headlight housing from engine compartment. Twist round plastic ring lock, unplug terminal, reverse your steps. Good Luck........


How do you change the door lock on a 1999 vw jetta When I turn the key nothing happens. Are there any troubleshooting steps to take before replacing the whole lock assembly?

Remove the inside door panel. Remove the door lock linkage. Remove the door lock barrel retaining ring. Reverse the process to install the new door lock.


What is a right hand reverse lock?

A painful hold in wrestling.