answersLogoWhite

0

To remove the key from the spindle nut, first loosen the nut using the appropriate tool. Once the nut is loose, slide the key out of the keyway on the spindle shaft by grasping it firmly and pulling it out. Be cautious not to damage the key or the spindle during this process.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

During which phase of mitosis are chromosomes attaching to the spindle?

Chromosomes attach to the mitotic spindle during the metaphase of mitosis. Part of the answer depends on how you define the stages of mitosis and not everybody does this the same way. The short answer is all of them.


What will these spindle fiber eventually be used for?

There are six phases of mitosis (a way which allows cell to reproduce itself so that organisms can grow). In this process, DNA is coiled into chromosomes. In the second phase, the spindle fibers attach themselves to centromere - centromere is a part of chromosome linking two sister chromatids (2 chromsatids make one chromosome). In the fourth phase, these spindle fibers shorten themselves and the sister chromatids are physically separated by the action. This way the two diploid daughter cells produced in mitosis have 46 chromosomes each.


How long will it take for a metal key to sink to the floor of a lake?

Depends on the depth. A key alone isn't dynamically stable, so it'll sort of wiggle its way down. Might need a second or two for each yard.


What is Kruckenberg's spindle?

Wiki said Krukenberg's spindle is the name given to the pattern formed on the inner surface of the cornea by pigmented iris cells that are shed during the mechanical rubbing of the posterior pigment layer of the iris with the zonules that are deposited as a result of the currents of the aqueous humor.


Why does the nuclear envelope break down in prophase?

If the nuclear envelope didn't break down, the spindle would not attach to the kinetochore proteins on the condensed chromosomes in prometaphase because the nuclear envelope would be in the way.

Related Questions

How do you remove the half shafts on a 1997 Buick Park Avenue?

They pull right out after removing the wheel, caliper, brakes, rotor, axle nut and possibly the tie rod nut or ball joint nut, to allow the spindle to swing out of the way.


Which way do you turn a nut to take it off?

Left


How do you replace front wheel bearing on 2007 Jeep Compass?

Remove the spindle from the car. You'll have to take off the axle nut, brake caliper, tie rod end, lower ball joint bolt, lower strut bolts and abs sensor to remove the spindle. Now you can take the spindle to a shop with the new bearing and have them install the bearing for you. Or you have access to a shop press you can do it yourself. Note: Shop presses can be dangerous! Press the wheel hub out of the spindle, then press the bearing out of the spindle. Pay close attention to the bearing you removed. (There is a magnetised side of the bearing and must be installed in the same way when putting the new bearing in. Magnet goes toward the sensor) Now reassemble the spindle in reverse order. That's the way I did it anyway. Good luck


How do you replace craftsman mower deck spindle bearings?

One can look in the owners manual of the Craftsman mower to learn how to replace the spindle bearings. Another way the spindle bearings can be replaced is to take it to a lawnmower professional.


Can Axle nut be too tight on Ford Escort?

Ideally, you want the spindle nut to hold the bearing pack together. Too tight and your bearings wear faster. WAY too tight and the bearings crush. Too loose and the bearings chatter. WAY too loose and the wheel wobbles.


What are the purpose of wheel center caps?

Center caps were originally meant to keep dirt away from the spindle nut and wheel bearings. Now they are mainly a decorative way to hide the lugnuts.


How do you replace front Wheel bearing on BMW?

Remove the tire from the vehicle and the caliper on the rotor. Remove the rotor from the vehicle by removing the 3 retaining bolts that hold the rotor to the hub (bearing) and the dust cover. Cut or bend the tabs on the axle nut so you can remove the axle nut from the spindle. Remove the hub (bearing) from the spindle. Try to wiggle it off if possible. If not, then lightly hit it on the rear of the hub to remove it from the spindle. One it's off remove the inner race with a locking 3 jaw puller and the inner dust cover. Clean the spindle and install the new inner dust cover. Lightly tap it on so it's seated all the way. Grease the spindle lightly and install the new hub. You will have to use a special tool (Bearing/Race installer) to make sure you don't damage the new hub or remove the outer race from the hub. Seat the hub all the way on the spindle and install the rotor, retaining bolts and new axle nut. The axle nut needs to be tightened to 200#. Make sure you don't over-tighten the axle nut. It could lead to wearing out your new bearing prematurely. Bend the tabs in on your axle nut put the new dust cover on (You can use the old one if it's not damaged) and put everything back together.


How do you change the front wheel bearings on a 1998 GMC jimmy?

this wheel bearing is sealed and the whole bearing needs to replaced. take tire off and brake assembely. bungie cord the brake calliper out of the way and so the weight is not all hanging on the brake line. take the cap off the nut that is held by a pin. next step your problably don't have the proper tools to do. but you need to have a deep well socket that will fit that nut that's on the spindle. the hardest part will be to remove that nut. with a proper air gun and that socket you can get that off easily. once that's off take off the rotor and bearing put the back on the rotor and put back on spindle . that nut that was so hard to take off needs to torqued back on at manufacture specs put cap and pin in and put back brake assembly. i.e take cap off brake fluid so the brake callipers come off more easily and on.


How do you remove drive shaft 1996 probe?

remove nut in center of rotor lift vehicle & separate ball joint pull drivshaft out of rotor/hub assembly as you swing spindle out of the way pull or pry out driveshaft


How do you manually shut a Volvo xc70 sunroof?

ok you going to have to take down the overhead liner about half way to get easy access to it but you may be able to do it and get to the motor if you take of the lights and sunroof switch cover above this way will take more patience but is better if you take the liner down, than you will see Allen insertion for an Allen key, set it in and turn to the right over and over again until close, aight man peace


How do you replace the cv half shaft on a 1993 Toyota Camry?

Loosen the nut on the end of the axle while the car is still on the ground. Jack the car up and support it. Take the lower ball joint loose either by taking it out of the spindle or take the 3 bolts out of the lower control arm. You may have to take the tie rod loose also depending on how much play there is. All cars a a little bit different. Remove the nut and washer from the end of the axle and swing the brake assembly and spindle out of the way. Put a large flat screwdriver or pry bar between the inner end of the axle and the transmission and pop the old axle out. If it is a two piece axle, take the clip out holding the axle in the center support before you try and pop out the axle. To put the new one in, slide it in the transmission making sure the splines are lined up and pop it in place. Reverse the process with the brakes and spindle.


What way do you hit the fan clutch nut to take off water pump?

left.....counterclock wise