0
The number of amps a horsepower (HP) motor uses when connected to a variable voltage, phase, and frequency (V pH Hz) line depends on the motor's efficiency, voltage, and load conditions. A general rule of thumb is that a 1 HP motor typically draws about 10 amps at 120 volts or about 5 amps at 240 volts under full load conditions. However, this can vary based on the motor's specific design and operating conditions. To get an accurate amperage, it's best to refer to the motor's nameplate or specifications.
What else can I help you with?
18kW motor will take how many amps?
To calculate the amps drawn by an 18kW motor, you can use the formula: Amps = Power (Watts) / Voltage (Volts). Assuming a standard voltage of 120V, the motor would draw approximately 150Amps. Note that actual amps will depend on the specific voltage of the motor.
How many amps does a garage door motor use?
A typical garage door motor uses about 3-5 amps while operating. This may vary depending on the specific model and size of the motor. It's important to check the motor's specifications for precise information.
How many amps does line 6 have?
Line 6 specialize in modeling amplifiers, software that is used for recording and digital modelling for guitars. There are 6 guitar amps made by Line 6.
Is a pool pump motor drawing half the amps listed on its nameplate a problem with the windings?
A pool pump motor which is drawing half the amps listed on its nameplate can indicate a problem with the windings or a lack of incoming current. Pumps will only draw as many amps as are required to operate under the current load.
How many amps for 1hp 3phase?
For a 1hp 3-phase motor, the current draw will depend on the voltage supply. Typically, at 230V, a 1hp 3-phase motor will draw around 3.6 amps. However, this value may vary based on the motor efficiency and power factor.
How many amps does a 30HP motor use hooked to 480v 3 pH 60Hz line?
The electrical code states that a 30 HP induction motor at 460 volts three phase will draw 40 amps. <<>> I = 33.34 AMPS IF EFF.= 95% AND P.F.= 85%
18kW motor will take how many amps?
To calculate the amps drawn by an 18kW motor, you can use the formula: Amps = Power (Watts) / Voltage (Volts). Assuming a standard voltage of 120V, the motor would draw approximately 150Amps. Note that actual amps will depend on the specific voltage of the motor.
How many amps are in a twelve volt motor?
That depends entirely upon the type of motor. A car starting motor may take a few hundred Amps for the short period.
How many amps will 8 d batteries generate?
Depends on the load, and on how the cells are hooked up, series or parallell.
How many amps in four C batteries in series?
C batteries use 1.5 volts. The number of amps depends on what device it is hooked up to. An average for four C batteries would be about 16 amps.
How many amps will a 75KW 525v motor draw?
23
How many amps does a 15 hp motor draw?
To answer this question the voltage of the motor must be stated.
1997 Neon How many amps is the cigarette lighter plug rated for?
Check the fuse that the cigarrete lighter is hooked up to.
How many amps will a 24 volt dc motor draw if running at 12 volts?
Depends on how big the motor is. A stronger motor will draw more amps then a weaker or less efficient motor. For example a wiper motor draws far less then a starter motor.
How many amps does a garage door motor use?
A typical garage door motor uses about 3-5 amps while operating. This may vary depending on the specific model and size of the motor. It's important to check the motor's specifications for precise information.
Why is my single phase induction motor drawing to many amps?
I have a single phase induction motor. It draws 8 amps on start up and climbs to 14-15 amps when I put a load on it. When I don't have a load it runs at 1 and climbs to 2-3 amps. It is normal operation for this motor to run at the lower number of amps with a load. But I don't know what is wrong.
How many amps will a 120 kw dc motor require?
Depends on the voltage.
