answersLogoWhite

0

Current rating must be equal, in both the points wiring.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

Can you change outlet to fit old 3 prong outlet?

An old 2 hole receptacle can be changed to a 3 hole receptacle that will accept a 3 prong plug, provided a ground wire is available at the box and connected to the ground (green) lug on the new receptacle. A 2 hole receptacle has a hot and neutral wire, while a 3 hole receptacle will require a ground wire connection -- in addition to the hot and neutral wires.


How do you wire a three prong twist lock receptacle to a 4 prong male connector in 220V?

To wire a three-prong twist lock receptacle to a four-prong male connector for 220V, you will need to connect the two hots, neutral, and ground wires from the male connector to the appropriate terminals on the receptacle. Make sure to follow the specific wiring diagram for your receptacle and connector to ensure proper installation and safety. If you are unsure or unfamiliar with electrical wiring, it is recommended to seek the assistance of a licensed electrician.


What does a 14-50R receptacle look like?

A 14-50R receptacle is commonly used for electric stoves and RVs. It typically has four straight blade prongs: two hot prongs, a neutral prong, and a ground prong. The prongs are arranged in a vertical line, with the ground prong typically being L-shaped.


Is a grounding 120 volt receptacle larger than an ordinary receptacle?

No, it just has an additional conductor to separate the neutral from the ground, and has a third prong in the receptacle to receive the appliance grounding conductor through the cordset.


Can you plug a 3 prong extension into a 110 volt outlet?

Yes, a 3-prong extension cord can be plugged into a 110-volt outlet as long as the prongs match the outlet. Just make sure the extension cord is rated for the appropriate voltage and current to avoid any electrical hazards.

Related Questions

Behind info switch panel is a 3 prong wire connection that has 2black wires in 1inlet 2 red wires in another and 1 green in last inlet in a 1986 corvettewhat is plugged into this receptacle?

The Flux Capacitor


Can you change outlet to fit old 3 prong outlet?

An old 2 hole receptacle can be changed to a 3 hole receptacle that will accept a 3 prong plug, provided a ground wire is available at the box and connected to the ground (green) lug on the new receptacle. A 2 hole receptacle has a hot and neutral wire, while a 3 hole receptacle will require a ground wire connection -- in addition to the hot and neutral wires.


How do you wire a three prong twist lock receptacle to a 4 prong male connector in 220V?

To wire a three-prong twist lock receptacle to a four-prong male connector for 220V, you will need to connect the two hots, neutral, and ground wires from the male connector to the appropriate terminals on the receptacle. Make sure to follow the specific wiring diagram for your receptacle and connector to ensure proper installation and safety. If you are unsure or unfamiliar with electrical wiring, it is recommended to seek the assistance of a licensed electrician.


How long can you leave block heaters on with out hurting engine?

I don't know in years but you can leave it plugged in for over the winter and it be fine. Just make sure you use a three prong extension cord when plugging it in. The block heater should be a three prong plug as well.


What is the proper electrical requirement for a 30 amp dryer receptacle?

The proper electrical requirement for a 30 amp dryer receptacle is a dedicated 240 volt circuit with a 30 amp circuit breaker and a 3-prong or 4-prong outlet.


What does a 14-50R receptacle look like?

A 14-50R receptacle is commonly used for electric stoves and RVs. It typically has four straight blade prongs: two hot prongs, a neutral prong, and a ground prong. The prongs are arranged in a vertical line, with the ground prong typically being L-shaped.


How do you covert a two prong welder plug to a three prong and ground out let?

Need to know the amperage rating of the plug or the NEMA configuration of the plug and receptacle


Who sells 8 ft 3 prong dryer cords?

Under the new electrical code rules three prong dryer cord receptacles and therefore cords are not allowed to be installed. As you are finding out, stores are not carrying them in stock any more. You should consider an upgrade for safety sakes, to a four prong plug cord and change the wall receptacle to a four prong receptacle. There are instructions on how to do this your self on Answers.


Is a grounding 120 volt receptacle larger than an ordinary receptacle?

No, it just has an additional conductor to separate the neutral from the ground, and has a third prong in the receptacle to receive the appliance grounding conductor through the cordset.


Can you plug a 3 prong extension into a 110 volt outlet?

Yes, a 3-prong extension cord can be plugged into a 110-volt outlet as long as the prongs match the outlet. Just make sure the extension cord is rated for the appropriate voltage and current to avoid any electrical hazards.


What is the third prong in a polarized receptacle used for?

I'm pretty sure that the third prong goes to the ground wires. for some things that have alot of watts they need to be grounded or something like that. like ext. cords. hope this helps!


If you have an electrical outlet that has 2 prongs you have a room heater which has 3 prongs - you have attached a 2 prong adapter however after a while the adapter melts Should you buy a new one?

What should be done in this situation is to change out the two blade receptacle to a three blade receptacle. Depending on how old the house wiring is, will depend on whether there is a ground wire in the two wire cable that the house was wired with. It sounds like the old two blade receptacle is worn out and it is the looseness between it and the adapter that is causing the problem. A room heater can be about 1500 watts and that adjusts to 12.5 amps that is heating up and melting your adapter. A new three blade receptacle will be tighter and it will not heat up. If there is a ground wire in the back of the receptacle's junction box attach it to the new receptacle. If there isn't a ground wire in the junction box, replace the receptacle anyhow, it will be much safer that the set up that you have now.