the time was 10:10
To set a Vollmond Atomic Wall Clock, first install the batteries and wait for it to receive a signal from the atomic clock. Once the time is set automatically, you can manually adjust it if necessary using the buttons on the clock. Refer to the user manual for specific instructions for your model.
We have H and M buttons right below the clock. Hold on H button to change hours and M button for Minutes. See this video below for more help:
To set the time on a 1990 300zx clock, first, press and hold the "clock" button until you see the hour digits blinking. Use the "tune" knob to set the correct hour. Press the "clock" button again to make the minute digits blink, and use the "tune" knob once again to adjust the minutes. Finally, press the "clock" button one more time to save the new time setting.
To set atomic clock model 86715, start by locating the time zone switch on the back of the clock and ensuring it is set to the correct time zone. Next, press and hold the "SET" button until the time display starts flashing. Use the "+" and "-" buttons to adjust the hours and minutes to the correct time. Finally, press the "SET" button again to confirm the time setting.
To set your clock, adjust it according to the correct time zone you're in. You may need to change the time on your clock for Daylight Saving Time, depending on your location. Use a reliable time source for accuracy.
First you get a clock. Next look at your Phone then use the time on you phone to set the time.
the clock is set for time
It is easy to set a Brookstone Atomic Clock. First, one must install the batteries. Then, follow the instructions on the screen to set the time to the correct time.
To set a Kincaid clock, first locate the time-setting knob, usually found on the back or side of the clock. Pull the knob gently to the first position to adjust the time; turn it to set the correct hour and minute. Push the knob back in to lock the time in place. If your clock has a pendulum, make sure it’s swinging freely after setting the time.
To set the time on a Dreamer Clock, first locate the "Set" or "Time" button, usually found on the back or side of the clock. Press and hold this button until the display starts blinking. Use the hour and minute buttons to adjust the time, then press the "Set" button again to confirm your changes. Finally, ensure the clock is set to AM or PM if applicable.
To set a Lorell HD-1688 wall clock, first, locate the small knob on the back of the clock. Turn this knob to adjust the time by moving the hour and minute hands to the desired position. Ensure the clock is set to the correct AM or PM time if applicable. Once set, hang the clock back on the wall and check that it is keeping accurate time.
To set the time on a Sharp Accu-Set clock model SPC991, first, locate the "Time Set" button on the back or bottom of the clock. Press and hold this button until the time display starts blinking. Use the "Hour" and "Minute" buttons to adjust the time to the correct hour and minute. Once the time is set, release the "Time Set" button to save the new time.
How do you set the time on a S10/Scan atomic clock model 86715
How do I set the time on the clock on a 1995 Mercedes C220
uhm i dont think you can set an alarm clock, but you can have a clock on your zune. go to settings and scroll till you see clock, click 'show clock' to yes and set the time to either 12 or 24 hour setting then set your time
To set the clock in a 1991 Dodge Stealth ES, first, turn on the car's ignition. Press and hold the "Clock" button until the display starts flashing. Use the "Hour" and "Minute" buttons to set the correct time, then press the "Clock" button again to save your settings. The clock should now display the updated time.
To set the Sharp Accu-Set Round wall clock model SPC991, first ensure the clock is powered on. Press and hold the "SET" button until the hour digits begin to flash. Use the "HOUR" and "MINUTE" buttons to adjust the time accordingly, and then press "SET" again to confirm the changes. The clock will automatically synchronize the time after setting.