answersLogoWhite

0

In North America both legs of the 240 volt supply are "hot" to ground. A two pole switch is used to break both legs from the supply. If only a single pole switch is used one leg will open and the tank would not operate but if you were depending on the switch to isolate the supply it could be dangerous. The other leg could lead to a shock if you touched the unswitched leg to ground while working on the tank.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

What heating element would you switch on to heat the whole tank?

You would switch on an immersion heater to heat the entire tank. It is designed to heat water in tank systems by immersing in the water and heating it directly.


Adding a 240 volt 20amp electric heater in my crawl space Would like to use my 20 amp circuit for outside condenser Both would never be on at the same time Do they make a switch for this?

Yes, what you are looking for is a double pole double throw switch. The center lugs are connected to the incoming line. Then the top lugs could be connected to the electric heater and the bottom lugs connected to the condenser. The trouble lies in finding a switch with a rating of 20 amps. These types of switches are usually used with a stand-by generator and rated at 100A and greater. Think I remember seeing one at 60A once. You might want to think of using a DPDT relay rated at 30A with a 120 volt coil. With a switch to operate it the relay. Depends in what part of the country you live, long winters switch off for heater, long summers switch off for conderser.


What does the abbreviation DPDT stands for what type of switch?

A DPDT switch is a Double Pole Double Throw switch


Why electric heater give electric shock when it switch was off?

An electric heater may give a shock when the switch is off due to a few reasons, such as faulty wiring, improper grounding, or a malfunctioning switch. If there is a short circuit or insulation failure, voltage can still leak to the metal parts of the heater. Additionally, static electricity buildup can also cause a mild shock. It's crucial to ensure that the heater is properly maintained and inspected to prevent such hazards.


What is the necessity of the starter.Can a single pole switch replace it?

A motor starter usually has an overload heater incorporated into it. A single pole switch does not have that type of protection. There are many brands of fractional motor starter switches. These types of switches are sized by the motors full load amperage. These types are dual purpose being that they can be used as the motors isolation switch and also they can be used as motor protection for the connected motor.

Related Questions

How do you wire an immersion timer switch?

To wire an immersion timer switch, first, ensure the power supply is turned off at the circuit breaker. Connect the live wire (usually brown) from the power supply to the input terminal of the timer switch, then connect the output terminal of the timer to the live wire leading to the immersion heater. Connect the neutral wire (usually blue) directly to the immersion heater. Finally, secure all connections and restore power to test the timer functionality. Always follow local electrical codes and consider hiring a qualified electrician if unsure.


What heating element would you switch on to heat the whole tank?

You would switch on an immersion heater to heat the entire tank. It is designed to heat water in tank systems by immersing in the water and heating it directly.


What is the purpose of the 90987-04002 relay for Toyota?

Fan (heater/air conditioning) relay switch


If there is power to the off switch for the heater is the switch gone?

If you are talking about a wall switch for the heater, check to see if the heater has its own internal thermostat or switch as this might be in the off position and not allow the heater to turn on. If you are talking about a switch on the heater itself, then yes in all probability the switch is not working.


Where is heater relay switch on 2001 Ford Expedition?

Where is heater control switch


What is the purpose of a high limit switch in a water heater and how does it function to ensure the safety and proper operation of the appliance?

The purpose of a high limit switch in a water heater is to prevent the water from overheating, which can lead to dangerous situations like fires or explosions. The switch works by monitoring the temperature of the water and shutting off the heating element if it reaches a certain, preset limit. This helps to ensure the safety and proper operation of the water heater by preventing it from reaching dangerously high temperatures.


Where is the heater relay switch on a 2005 Malibu max?

Where is the heater relay switch on a 2005 MalibuRead more: Where_is_the_heater_relay_switc


Isuzu trooper seat heater switch?

IT turns the heater on and off!


How do I turn on the heater in my house?

To turn on the heater in your house, locate the thermostat and set it to the desired temperature. Then, switch the heater on using the power button or switch. Wait a few minutes for the heater to start producing warm air.


Why is your fan heater control switch is permanently on full even though the switch is on off?

It could be the high speed heater motor relay is stuck on or the switch itself is broken.


Why would heater only blow hot air when you turn the temp switch down Replaced temp switch and still does it?

A restricted/plugged heater core can do that. Try flushing the heater core.


Why will the heater in a 1996 Grand Am with 4 pos heater switch not work on HIGH but it works in all 3 other positions?

Your heater switch may not need to be replaced. The heater high position is controlled by a fuse under the hood. Until you find the fuse and replace it, your new switch will not work. JRR.