0
What else can I help you with?
What wire size do you need for a 3phase 80amp 60hz 220v load amp 68?
A #4 copper conductor with an insulation factor of 75 or 90 degrees C is rated at 85 amps. This size wire will also be the same for a load amperage of 68 amps as the next wire size smaller #6 is only rated at 65 amps.
What size of wire should be used for 60Hz?
The frequency has no direct relationship to the size of wire. Wire is sized as to the amount of current a load draws in a circuit.
How do you wire a three wire 220v for dryer White to white but where does black and ground go?
If the cable you are trying to connect the dryer up to only has a white, black and ground wire, then the dryer is not going to work. The cable needs to be a three wire, the ground wire is never counted when discussing house wiring. Open up the electrical access panel on the back of the dryer. You will see a terminal block. A red and black and white connect to this terminal strip. The "hot" wires are connected to the outside terminals. The neutral (white) wire will be in the center. Connect the ground wire to the frame of the dryer. It is very important that this ground wire be connected as this is the wire that carries the fault current to trip the breaker should a fault arise.
How many wires does a straight 220V circuit have?
A straight 220V circuit typically has 2 wires - one hot wire (typically black or red) and one neutral wire (typically white). These wires are used to carry the electrical current to and from the device being powered.
How do you connect red white black and green form USB to a two wire cable having red lack?
You can connect the red wire from the USB cable to the red wire of the two-wire cable. The black wire from the USB cable can be connected to the black wire of the two-wire cable. As for the white and green wires from the USB cable, since the two-wire cable only has a red and black wire, you can leave the white and green wires unconnected as they are not needed in this case. Just make sure to insulate the unused wires properly to avoid any short circuits.
What is the diagram for converting a 4-wire 220V connection to a 3-wire 220V connection?
To convert a 4-wire 220V connection to a 3-wire 220V connection, you will need to remove the neutral wire and connect the ground wire to the neutral terminal. This diagram shows the proper wiring configuration for this conversion.
What is the recommended wire size for a 220v electrical circuit?
The recommended wire size for a 220v electrical circuit is typically 10-gauge wire.
What is the recommended wire size for a 220v 20 amp circuit?
The recommended wire size for a 220v 20 amp circuit is typically 12-gauge wire.
What is the recommended wire size for a 220v 30 amp circuit?
The recommended wire size for a 220v 30 amp circuit is typically 10 gauge wire.
What is the appropriate wire size for a 20 amp 220v circuit?
The appropriate wire size for a 20 amp 220v circuit is typically 12-gauge wire.
What is the appropriate wire size for a 220v 30 amp circuit?
The appropriate wire size for a 220v 30 amp circuit is typically 10 gauge wire.
What is the recommended wire size for a 60 amp 220v circuit?
The recommended wire size for a 60 amp 220v circuit is typically 6-gauge wire.
What are the step to create cross network cable?
To create a Crossover Cable, wire one connecter to the T568A Network Standard and wire the other connector to the T568B Network Standard, so the cable 'crosses over', A becomes B and visa versa.
What is The Voltage Of each wire in Straight 220V Circuit?
Voltage is not an absolute figure. Voltage Difference is the exact term. So, the voltage difference between the two wires in the 220 V circuit will be 220V.
Why is there a wire not attached in the fuse box of a 1993 Chevy blazer?
This might be a cable for some additional feature your car is not equipped with, but the wire is included in the standard cable assy
What is the appropriate wire size for a 220V 20 amp circuit?
For a 220V 20 amp circuit, the appropriate wire size is typically 10 AWG (American Wire Gauge) for copper conductors.
Is the neutral wire on a 220v outlet the same as the ground?
No it is not
